Microduino Butterfly Light

Outline Project： Butterfly light Purpose： Butterfly light is a touch control color-changing music light. Difficulty: Middle-level Time-consuming: 6-Hour Maker: Guysgogo&&Microduino Team Introduction 文件:Setup gusgogo logo.jpg 80px Guysgogo is team composed of four senior students in the maker class of LKK Intelligent Hardware Industrial Design. Three of the students—Run Jiang, Huiyu Hao, Tingyu Li and Chaohui Xie, are college students from Hebei.

Bill of Material Microduino Equipment Module Number Function Microduino-Core+ 1 Core board Microduino-USBTTL 1 Program download Microduino-Audio 1 Audio control Microduino-Amplifier 1 Amplifier module Microduino-Sensorhub 1 Sensor connection board Microduino-Cube-S1 1 Base board Microduino-Lantern 7 Colorful LED light Microduino-Touch 7 Touch sensor Other Equipment Equipment Number Function Loudspeaker 1 MicroUSB cable 1 Power supply Document Program download: Butterfly_light 3D model download: 文件:3D-Butterfly light.zip Build 3D Model The model adopts buttery shape. 文件:3dm light1.jpg 600px Build Hardware Circuit The colorful LED light adopts built-in IC control chip. With one-wire bus control, you only need one I/O port to control. Just connect the OUT interface of one Lantern to the IN interface of the other Lantern, and then join up the IN interface to Microduino core board via Sensorhub. 文件:Light steup.jpg 600px Each touch sensor needs a Microduino I/O port to drive. We can tell if it is pressed by reading sensor values via digital port and analog port. 文件:Touch steup.jpg 600px You can debug software after building the hardware circuit. Prepare Audio Download audio file：文件:Music-Butterfly light.zip Connect Microduino-Audio module with your computer via USB cable. It will show a disk named “microduino” after successful connection. Just open the disk and select audio file, then write to flash. Software Debugging Program Description “audio.h”file is used for music play control and “key.h” file is for touch detection. Audio module is connected to Serial 1 to control by default. As for touch sensor pin definition, users can change according to personal needs: int sensor_pin[7]= { 4,8,10,12,A0,A2,A6 }; The colored LED light defines seven lights, whose light control pin is D6: #define PIN 6 Adafruit_NeoPixel strip = Adafruit_NeoPixel(7, PIN, NEO_GRB + NEO_KHZ800); How to judge the touch of seven lights & how to control music and LED lights: When pressing some a button, it will play music and the white led light will blink. When pressing twice one time, the white led will go on. When pressing three times once, you can change the light color. Anytime, one press means turning off the light. for(int a=0;a<7;a++) { { if(key_get(sensor_pin[a],1)) //When triggered, { //colorWipe(strip.Color(255, 255, 0), 10); sensor_vol_cache[a]++; //Counting // Serial.print("+"); if(sensor_vol_cache[a]>3) sensor_vol_cache[a]=3; { colorWipe(color[8], a); num=a; audio_choose(a+1); audio_play(); colorWipe(color[0], a); } time1[a]=millis(); } if(millis()-time1[a]>500 && sensor_vol_cache[a]!=0) //Just start it and delay for one second or more, and the scan is ended. { if(sensor_vol_cache[a]==1) { colorWipe(color[0], a); Serial.println("LED_OFF"); } else if(sensor_vol_cache[a]==2) { colorWipe(color[8], a); } else { randomSeed(millis()%1000); sensor_vol[a]=random(1,7); Serial.println(""); Serial.print("num:"); Serial.print(a); Serial.print(":"); Serial.print(sensor_vol[a]); colorWipe(color[sensor_vol[a]], a); } sensor_vol_cache[a]=0; //Return to zero and wait for the next scan. } } } Program Download Make sure you build Microduino IDE, or you can refer to:Microduino Getting start. Make there is _99_LCD_NeoPixel library in IDE. Open the downloaded program and select the right board to download after compiling. After the download, you can test whether the function mentioned above is right or not by the Touch sensor. Meantime, you need to notice which LED light the Touch sensor corresponds to. Overall Assembling Fixate the light and the touch sensor on the outside of the 3D battery. 文件:Setup 3d light1.jpg 600px 文件:Setup 3d light2.jpg 600px Wrap the battery with a beautiful exterior. 文件:Setup 3d page.jpg 600px Fixate the loudspeaker on the base and then get it fixated with the battery. 文件:Setup 3d buzzer.jpg 600px Plug in USB cable for power supply at last and have fun! 文件:Setup 3d ok1.jpg 600px 文件:Setup 3d ok2.jpg 600px Notice Since Audio adopts Serial 1 by default, please initialize Serial 1: “AUDIO_PORT.begin(9600);” Please make sure the touch sensor corresponding with the lights. Video http://v.youku.com/v_show/id_XODc2NDMzODg4.html