|
Microduino USBHOST mainly offers the USB host function for devices, supporting USB host controller and USB peripherals, such as mobile phones with OTG function, keyboards, joystick, and camera.
Features
- Support MicroUSB interface；
- Small, cheap, stackable and open;
- Open hardware circuit design and Arduino compatible programming development environment;
- Uniform Microduino interface standard and rich peripheral modules, capable of having a fast and flexible connection and extension with other modules and sensors in accord with Microduino interface standard;
- Easy to be integrated to pegboards with a 2.45-pitch female header connector interface.
Specifications
- Electrical specifications
- 3.3V or 5V power;
- 5V/500mA power protocol of the USB host;
- Adopt TC74HC4050 level conversion chip and ensure high anti-interference and stable output;
- D+, D- and VBCOMP with ESD protection function;
- The internal D+ pull-up resistor (peripherals mode) and D+/D- pull-down resistor (host mode) controlled by firmware/hardware;
- Communication
- Compatible with MAX3420 MAX3420E USB peripheral device control software with SPI interface;
- Comply with USB 2.0 specification (12 Mbps peripherals at full speed and 12Mbps/1.5 Mbps host at full speed/low speed);
- Smart USB SIE；
- Automatic processing of USB flow control and double buffer;
- Process low level USB signaling.
- Device Support：
- HID devices, such as keyboards, mouse, joystick and so on;
- Game controller: Sony PS3，Nintendo Wii and XBOX360；
- USB-to-serial converter: FTDI，PL-2303，ACM and mobile phones with OTG function and GPS receiver;
- Android mobile with ADK function；
- Digital Camera: Canon EOS's Powershot, Nikon digital SLR cameras and P&S as well as general PTP;
- Mass storage devices, such as U disk, card reader and the external hard drive；
- Bluetooth dongle.
| Chip Pin |
Microduino Pin |
Function
|
| RES |
RST |
reset chip
|
| SCLK |
D13 |
SPI serial clock input
|
| SS |
D5 |
SPI slave select input
|
| MISO |
D12 |
SPI serial data output
|
| MOSI |
D11 |
SPI serial data input
|
| INT |
D4 |
Interrupt output
|
Document
Eagle PCB local download
Main components：
Development
An ordinary Bluetooth adapter. You can easily add different Bluetooth services, such as a PS3 or Wii controller or SPP which is supported through Bluetooth virtual serial port. A number of different examples can be found in the examples directory.
Connect USB peripherals. Such as a mouse, handle etc.
Connect HID devices via Bluetooth, currently supports HID mouse and keyboard.
Allow you send data to your Microduino from PM/mobile phone via Bluetooth.
Allow you to use the Sony PS4 controller via Bluetooth and USB.
Use DUALSHOCK3, navigation or motion controller via Bluetooth and USB.
- Xbox Libraries：
- Xbox Libraries：
The library uses USB as the Xbox 360 controller.
Application
Light a LED via a mobile using the ADK example library：
Prepare work
- Prepared hardware：Microduino FT232R, Microduino Core, Microduino USBHOST, OTG cable, make sure your Android device supports and turn on the USB debug mode, USB cable；
- Prepared software：USB_Host_Shield_2.0 library, Arduino IDE(1.0 release and upper);
- Uncompress the zip folder and rename to “USB_Host_Shield” becasue Arduino IDE doesn't support any special characters, then copy to libraries folder of Arduino IDE；
- Connect the Microduino FT232R and PC using USB cable to download program and serial monitor；
- Connect a LED to I/O port D6 of Microduino-Core；
Debug
- Open the example program "ArduinoBlinkLED" from ADK folder of examples；
- Change LED_BUILTIN to Microduino pin in "#define LED LED_BUILTIN", such as "#define LED 6". But can't be D13, because D13 is used as SCK.
- After compiled, select the board "Microduino Core (Atmega328P@16M,5V)", download directly；
- Connect the mobile phone and Microduino USBHOST by OTG cable and USB cable;
- Open the serail monitor, will display "Arduino Blink LED Started";
- The phone will automatically pop up the application "ArduinoBlinkLED", download and install it；
- After installed the application, will prompte to open the USB connection fittings, and click OK to enter the program interface;
- Successful connection will show "connected", and can control the LED light on and off via the button.
Bug
History
Picture
Front
Back
Video
|
