MCookie-BT

来自Microduino Wikipedia
跳转至: 导航搜索
Language English
mCookie-BT

mCookie-BT is low-consumption serial transmission module, which can communicate with other Bluetooth devices such as phone and ipad.






Features

  • Low power consumption
  • Support iBeacons ;
  • Small, stackable, open and cheap;

Specification

  • Way of Communication: Serial port transmission and the default serial port is D0(RX), D1(TX);
  • Power supply: +3.3VDC 50mA;
  • Status indicator:
    • Before Bluetooth connection
      • Host machine indicator keeps on for 100ms every second when not recording slave machine address; Host machine indicator keeps on for 900ms every second when recording slave machine address;
      • Slave machine indicator keeps on for one second every two seconds.
    • After connection:
*** The indicator of both the host and the slave machine keeps on for 100ms every five seconds.  
  • During the transmission, each data package should include less than 120 bytes. The higher the baud rate is, the longer transmission interval is. There exists loss rate during Bluetooth data transmission. So users should be ready for re-transmission or data check.
  • All AT instructions end with "\r\n " so you should choose "\r\n " while debugging under AT instructions. Most AT instructions work before connection and all data pass through after connection.
  • iBeacon has been integrated. Set by AT instruction “AT+MODE2\r\n” can be achieved only under slave machine.
Ble-rule.jpg
  • Way of Communication: Serial port transmission and the default serial port is D4(RX), D5(TX);
  • Power Supply: +3.3VDC 50mA;
  • Bluetooth Protocol: Bluetooth Specification V4.0 BLE;
  • Service Support: Central & Peripheral UUID FFE0,FFE1;
  • Frequency: 2.4GHz ISM band;
  • Way of Modulation: GFSK(Gaussian Frequency Shift Keying);
  • Transmit Power: ≤4dBm;
  • Flexibility: ≤-84dBm at 0.1% BER;
  • Transmission Rate:
    • Asynchronous: 6 kbps;
    • Synchronous: 6 kbps;
  • Status Indicator:
    • Before connection:
      • Host machine indicator keeps on for 100ms every second when not recording slave machine address;
      • Host machine indicator keeps on for 900ms every second when recording slave machine address;
      • Slave machine indicator keeps on for one second every two seconds.
**After connection: 
    • The indicator of both the host and the slave machine keeps on for 100ms every five seconds.
  • During the transmission, each data package should include less than 120 bytes. The higher the baud rate is, the longer transmission interval is. There exists loss rate during Bluetooth data transmission. So users should be ready for re-transmission or data check.
  • iBeacon has been integrated. Set by AT instruction “AT+MODE2\r\n” can be achieved only under slave machine.

Document

Support AT instruction configuration/control: 文件:Microduino-BLE.pdf

Development

Serial Communication Requirements

  • Default serial port configuration is:
    • Baud rate:9600
    • No check
    • data bit: 8
    • Stop bit: 1
    • Set as:" \r\n " "9600baud "
Serial-mcookie.jpg

Communicate with other BT devices via CoreUSB

  • Program
//Use soft SoftwareSerial
//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(4, 5);

//#define my_Serial mySerial
#define my_Serial Serial1 //Define serial communication as Serial1 
String msg = ""; //Define a string of characters 

void setup()
{
  // Initialize Bluetooth communication baud rate  
  my_Serial.begin(9600);
  // Initialize serial monitor communication baud rate 
  Serial.begin(9600);
}
void loop()
{
  //Receives signal once and give feedback once to the other communication side. 
  if (my_Serial.available() > 0)  //If there is data input in serial port 
  {
    msg = my_Serial.readStringUntil('\n'); //All content before acquiring line break
    Serial.println(msg);                   //Display character string of msg in the serial monitor  
    my_Serial.println("bluetooth respond");  //Send data to the other side of Bluetooth communication 
  }
}

Communicate with Android Device

  • Only version 4.3 or higher phone can communicate with mCookie-BT module
  • Download Android communication software and install it on the phone.

文件:BT—APP.zip

Step 1: Download program to mCoookie;

Download

Step 2: Start to set Android device. Open Bluetooth function of the device, copy and install ".apk " file from testing package to the phone, then open APP and open serial monitor on computer IDE side; Step 3: Click SCAN on top right of the APP and it'll show Bluetooth devices around you as follows:

App—蓝牙搜索

Click the corresponding Microduino Bluetooth number and enter the following interface:

App—蓝牙通信

Wait for 2-3 seconds and see "Ready" on the screen, meaning a successful connection between the phone and the Bluetooth. Click " Sync RTC With Phone " and see changes of "RT TIME" above and the serial monitor.

App—串口监视器
App—手机App

You'll see the phone receiving message " bluetooth respond " from mCookie and on the other side, the serial monitor also gets the time and content of the message. Thus, bidirectional communication function of Bluetooth can be verified.

Communicate with IOS Device

  • iPhone4s or higher, iPod touch 5 or higher, iPad 3 or higher and iPad mini or higher;
  • Come to App Store and download LightBlue
LightBlue

Step 1: Download program to mCookie;

Step 2: Install "LightBlue", open the software and start to set IOS device. And then open IOS device's Bluetooth function and open serial monitor on the computer's IDE side.

LightBlue on ble.jpg

Step 3: Open LightBlue: Enter Bluetooth device searching interface, find Microduino Bluetooth device from "Peripherals Nearby", Click this item and make its connection your phone.

Connection1

Enter the following interface after connection:

Connection2

Step 4: Select and click "Characteristic6" and see encoding format on the top right of the screen. (The default is Hex 16 band encoding.) Click Hex button if you need to display character strings and choose UTF-8 encoding format, click "Listen for notifications" and let your phone enter monitoring state.

Ble-Connection5.jpg

Step 5: Click " Write new value " and pop up text editing interface

Ble-Connection2.jpg

Enter a character string combined by English characters and numbers and check result from the phone and the serial port.

Ble-Connection3.jpg
Ble-Connection4.jpg

You can see from the picture that the serial port receives phone data "12345" and the phone side also gets return data " bluetooth respond " from Bluetooth, meaning the bidirectional Bluetooth communication is smooth.

Extension

Use AT to Check or Change BT Parameters

  • AT instruction configuration/control document:

文件:Microduino-BLE.pdf

  • Program
//Use other soft serial port " SoftwareSerial"   
//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(4, 5); // RX, TX

//#define my_Serial mySerial
#define my_Serial Serial1 //Define serial ports of CoreUSB and BT  

void setup()
{
  Serial.begin(9600);//Serial monitor communication & Baud rate
  my_Serial.begin(9600);//BT communication baud rate 
}

void loop()
{
  if (Serial.available())//Monitor data from serial monitor 
    my_Serial.write(Serial.read());//Wrote data into BT  
  if (my_Serial.available())//Monitor serial data of BT
    Serial.write(my_Serial.read());//Print data in the serial monitor 
}
  • Download program
    • Stack mCookie-BT and mCooikie-CoreUSB, plug USB cable to mCookie-CoreUSB on one side and connect to your computer on the other side;
    • Start Arduino IDE, copy program to IDE;
    • Choose Microduino CoreUSB from (toools)-> (Board) and select the right serial number from (tools)-> (Serial;
    • Click compile button (√) on the top left of IDE and start compiling. After that, click download (->) and burn the program to board;
  • Open serial monitor and set it to: "\r\n " "9600baud "
Serial
  • 在Enter fixed instructions in the serial monitor and you'll return result. (This reference file can change BT's parameters. )
AT

Change Serial Communication Pin

The default serial is D0(RX), D1(TX). Users can change serial port according to personal needs, which can refer to:

Ble-Serial-change.jpg

Use soft communication program:

//Use other soft serial "SoftwareSerial"  
#include <SoftwareSerial.h>
SoftwareSerial mySerial(4, 5);//Select the corresponding port numbers--(2,3) or (4,5) according to the serial ports.

#define my_Serial mySerial

String msg = "";

void setup()
{
  // Initialize Bluetooth communication baud rate 
  my_Serial.begin(9600);
  // Initialize serial monitor communication baud rate  
  Serial.begin(9600);
}
void loop()
{
  //Receive signal once and then give feedback to the other side of the communication.
  if (my_Serial.available() > 0)  //If serial port has data input 
  {
    msg = my_Serial.readStringUntil('\n'); //Acquire all content before line break  
    Serial.println(msg);                   //Receive character strings of msg in the serial monitor  
    my_Serial.println("bluetooth respond");  //Sending data to the other side of the Bluetooth communication 
  }
}

Project

Related Projects: Bluetooth Light Bluetooth Night Lamp


FQA

  • This module can’t make pair with win7?
    • Check the BT version in win7, this module only support BLE 4.0 version and default password is 000000.
  • Does this module can reset by button?
    • No, it can be reset by power down.
  • This module can’t make pair with iphone and Android phone?
    • This issue mostly is caused by the BT version. This module only supports BT4.0 protocol.
    • For Andriod OS: 4.3 release
    • For IOS: iPhone4s upper, iPod touch 5 upper, iPad 3 upper and iPad mini upper


Pictures

MCookie-BT-t1.jpg
MCookie-BT-b1.jpg
mCookie-BT Front
mCookie-BT Back