“Microduino-ENC28J60”的版本间的差异

来自Microduino Wikipedia
跳转至: 导航搜索
第40行: 第40行:
 
* 25 MHz Clock Input Requirement
 
* 25 MHz Clock Input Requirement
 
* Operating Voltage of 3.1V to 3.6V (3.3Vtypical)
 
* Operating Voltage of 3.1V to 3.6V (3.3Vtypical)
 +
 +
===引脚说明===
  
 
:[[file:Micrduino-Enc28J60-1.jpg|800px|thumb|center|Microduino-ENC28J60 Spec]]
 
:[[file:Micrduino-Enc28J60-1.jpg|800px|thumb|center|Microduino-ENC28J60 Spec]]

2014年2月11日 (二) 11:53的版本

Microduino-ENC28J60

Microduino-ENC28J60 must be stacked with Microduino-RJ45 together to form a complete Ethernet module, individual module can not be used seperately.

Microduino-ENC28J60 module is based on Microchip’s ENC28J60 stand-alone 10Base-T Ethernet controller. The ENC28J60 is a stand-alone Ethernet controller with an industry standard Serial Peripheral Interface (SPI). It is designed to serve as an Ethernet network interface for any controller equipped with SPI.

Microduino-RJ45 is the common name for an 8P8C modular connector using 8 conductors. It has dedicated pins for LED link and network activity indication.

Microduino-ENC28J60 meets all of the IEEE 802.3 specifications. It also provides an internal DMA module for fast data throughput and hardware assisted checksum calculation, which is used in various network protocols. Communication with the host controller is implemented via an interrupt pin, if required, and the SPI, with clock rates of up to 20 MHz.

Microduino-ENC28J60 + Microduino-RJ45 provide onboard low drop voltage regulator which supplies stable voltage to the Ethernet controller. It is an ideal device for applications involving Home/Office Automation, Remote Diagnostics systems, Industrial equipments, Security Systems and Robotics as well.

Features

  • ENC28J60 is a very popular Ethernet chip, the first version Arduino Ethernet extend board was based on EN28J60 chip, and therefore, ENC28J60 is widely adapted by designers due to its stability and easy to use.
  • Integrated MAC and 10Base-T PHY
  • support POE
  • IEEE 802.3. Compatible Ethernet Controller, fully Compatible with 10/100/1000Base-TNetworks
  • Using the U-Shape 27-pin interface (UPin-27), the standard interface of Microduino, must be used with Microduino-RJ45 for full functions
  • Delivered ready to plug in.
  • 2.54mm (0.1 inch) pin pitch, compatible to bread board and hole board


Specifications

  • OperatingSupply: 5V-9V DC
  • Onboard 3.3V low drop voltage regulator for Ethernet controller
  • Requires Hostmicrocontroller with integrated SPI
  • DirectHost to module connection via 9 pin berg strip connector (lengthy wiresare not recommended for SPI interface)
  • Supports One10Base-T Port with Automatic
  • Polarity Detection and Correction
  • Supports Full and Half-Duplex modes
  • Programmable Automatic Retransmit onCollision
  • Programmable Padding and CRC Generation
  • SPI Interface with Clock Speeds Up to 20MHz
  • 25 MHz Clock Input Requirement
  • Operating Voltage of 3.1V to 3.6V (3.3Vtypical)

引脚说明

文件:Micrduino-Enc28J60-1.jpg
Microduino-ENC28J60 Spec


ENC28J60模块引脚名 Microduino引脚 功能
SCK D13 SPI总线时钟
SI D12 数据输入脚
SO D11 数据输出脚
CS D8 SPI片选信 (程序中需要定义)
INT D2 中断功能(在此为INT0)
RST RST 复位功能

Documents

文件:Micromodule-ENC28J60-SCH.png
Microduino-ENC28J60 Schematic


Development

Buy

History

  • 2012年12月29日,第三版,修订bug,解决某些交换机不支持,丢包严重问题,感谢@护林人。
  • 2012年11月18日,第二版,确定Microduino I/O 管脚分布,重新布板并通过测试
  • 2012年11月8日,初版,测试功能基本完备

Pictures

Micromodule ENC28J60 Front
Micromodule ENC28J60 Back