Lesson 20--Microduino Two Digital Tube Countdown Display

来自Microduino Wikipedia
Pkj讨论 | 贡献2014年3月13日 (四) 12:24的版本 (Created page with "{{Language | 第二十课--Microduino 两位数码管倒计时显示}} {| style="width: 800px;" |- | ==Objective== We have learned display the number statically, this lesson w...")
(差异) ←上一版本 | 最后版本 (差异) | 下一版本→ (差异)
跳转至: 导航搜索
Language English

Objective

We have learned display the number statically, this lesson will teach you how to dispaly number dynamically. Only need change the code, no hardware change.

Equipment


Schematic

第二十课-Microduino 2位数码管倒计时原理图.jpg

Pin Table

Microduino Pin Digital Tube Pin
D2 10(A)
D3 9(B)
D4 1(C)
D5 4(D)
D6 3(E)
D7 6(F)
D8 5(G)
9 2(DP)
D10 8(LED1)
D11 7(LED2)

Program

byte digit0 = 10;	//Ten digits Microduino pin
byte digit1 = 11;	//Single digit Microduino pin
byte dotPin = 2;	//Decimal point pin

byte sevenSegmentPins[] = {2,3,4,5,6,7,8};	//A,B,C,D,E,F,G Microduino pin
byte sevenSegment[10][7] =
{
  //a b c d e f g
  { 0,0,0,0,0,0,1 },  // = 0
  { 1,0,0,1,1,1,1 },  // = 1
  { 0,0,1,0,0,1,0 },  // = 2
  { 0,0,0,0,1,1,0 },  // = 3
  { 1,0,0,1,1,0,0 },  // = 4
  { 0,1,0,0,1,0,0 },  // = 5
  { 0,1,0,0,0,0,0 },  // = 6
  { 0,0,0,1,1,1,1 },  // = 7
  { 0,0,0,0,0,0,0 },  // = 8
  { 0,0,0,1,1,0,0 }   // = 9
};

void setup()
{
	//Initialize all lights up
   pinMode(dotPin, OUTPUT); //pin 9
   pinMode(digit0, OUTPUT); //pin 10
   pinMode(digit1, OUTPUT); //pin 11

  for(int i=0; i<7; i++)
  {
    pinMode(sevenSegmentPins[i], OUTPUT);
  }
  digitalWrite(dotPin, HIGH);
  digitalWrite(digit0, HIGH);
  digitalWrite(digit1, HIGH);
}

//Display number
void segmentWrite(byte digit)
{
  byte pin = 2;
  for (byte i=0; i<7; ++i)
  {
    digitalWrite(pin, sevenSegment[digit][i]);
      ++pin;
  }
}

void loop()
{

  for(int i=9;i>=0;i--) {// Countdown ten digits
    for(int j=9;j>=0;j--) {//Countdown to single digit
      
      unsigned long startTime = millis();
      for (unsigned long elapsed=0; elapsed < 600; elapsed = millis() - startTime) {//Display 600ms
          digitalWrite(digit0, LOW);   //Trun on ten digits tube
          segmentWrite(j);             //Display single tube
          delay(10);                  //Delay 10ms
          digitalWrite(digit0, HIGH);  //Turn on ten digits tube
          digitalWrite(digit1, LOW);   //Turn off single tube
          segmentWrite(i);             //Display ten digits 
          delay(10);                  //Delay 10ms
          digitalWrite(digit1, HIGH);  //Turn on single digit
      }
      
    }
  }

}

Debug

Step 1:Identify the digitsl tube's Pin

Step 2: Copy code to IDE and compile it

Step 3: Set up circuit, as follows:

第二十课-Microduino 2位数码管倒计时连接图.jpg

Step 4: Run program

Setp 5: Observe the digital tube


Result

The number will countdown from 99 to 0, and then in circle.

Video

http://v.youku.com/v_show/id_XNjc4NjcxMzY0.html