“【识别标签ID】”的版本间的差异

来自Microduino Wikipedia
跳转至: 导航搜索
 
第62行: 第62行:
 
}
 
}
 
</source>
 
</source>
*3)确认天线已经连接好,如图所示。并且将标签放好,贴紧天线。
+
*3)确认读卡器已经连接好,如图所示。并且将卡片放好,贴紧读卡器。
 
[[file:NFC example1-2.JPG|thumb|center|600px]]
 
[[file:NFC example1-2.JPG|thumb|center|600px]]
 
*4)下载成功后打开串口监视器,波特率选择115200.
 
*4)下载成功后打开串口监视器,波特率选择115200.

2018年6月20日 (三) 09:28的最新版本

#include <Microduino_NFC.h>

NFC nfc;

void setup(void) {
  Serial.begin(115200);
  Serial.println("Hello!");

  uint32_t versiondata = nfc.begin();

  if (! versiondata) {
    Serial.print("Didn't find PN53x board");
    while (1); // halt
  }
  
  // Got ok data, print it out!
  Serial.print("Found chip PN5"); Serial.println((versiondata>>24) & 0xFF, HEX); 
  Serial.print("Firmware ver. "); Serial.print((versiondata>>16) & 0xFF, DEC); 
  Serial.print('.'); Serial.println((versiondata>>8) & 0xFF, DEC);
  
  // Set the max number of retry attempts to read from a card
  // This prevents us from waiting forever for a card, which is
  // the default behaviour of the PN532.
  nfc.setPassiveActivationRetries(0xFF);
    
  Serial.println("Waiting for an ISO14443A card");
}

void loop(void) {
  boolean success;
  uint8_t uid[] = { 0, 0, 0, 0, 0, 0, 0 };  // Buffer to store the returned UID
  uint8_t uidLength;                        // Length of the UID (4 or 7 bytes depending on ISO14443A card type)
  
  // Wait for an ISO14443A type cards (Mifare, etc.).  When one is found
  // 'uid' will be populated with the UID, and uidLength will indicate
  // if the uid is 4 bytes (Mifare Classic) or 7 bytes (Mifare Ultralight)
  success = nfc.readPassiveTargetID(PN532_MIFARE_ISO14443A, uid, &uidLength);
  
  if (success) {
    Serial.println("Found a card!");
    Serial.print("UID Length: ");Serial.print(uidLength, DEC);Serial.println(" bytes");
    Serial.print("UID Value: ");
    for (uint8_t i=0; i < uidLength; i++) 
    {
      Serial.print(" 0x");Serial.print(uid[i], HEX); 
    }
    Serial.println("");
    // Wait 1 second before continuing
    delay(1000);
  }
  else
  {
    // PN532 probably timed out waiting for a card
    Serial.println("Timed out waiting for a card");
  }
}
  • 3)确认读卡器已经连接好,如图所示。并且将卡片放好,贴紧读卡器。
NFC example1-2.JPG
  • 4)下载成功后打开串口监视器,波特率选择115200.
NFC example1.png
  • 5)可以通过串口观察到返回信息,可以看到标签的UID与UID长度。

到这一步就可以简单的形成一个NFC标签控制应用的基础了,通过识别正确的UID执行对应功能。