OLED显示屏使用

目的

了解Microduino OLED，并掌握如何驱动OLED显示屏。

设备

Microduino-OLED/zh

Microduino-Oled是基于SSD1306的0.96吋128x64 OLED显示模块。采用I2C接口，3.3V 电源供电。像素为128*64（128列*64行）。

Microduino-CoreSTM32/zh

Microduino-CoreSTM32小巧精悍，其内核来自于ARM公司具有突破性的Cortex-M3内核的32位闪存微控制器。该内核是专门设计于满足集高性能、低功耗、实时应用、具有竞争性价格于一体的嵌入式领域的要求。

Microduino-Weather扩展板

Microduino Weather模块集成了三种传感器，分别是光照强度传感器（TSL2561），数字气压传感器（BMP180），数字温湿度传感器（AM2321）。采用I2C接口与核心相连。广泛用于气象监测。

其他硬件设备

OLED转接线一根
USB数据线一根

文件:Advance9 1.jpg

600px

文档

12864Oled显示屏：2864HSWEG01 文件:2864HSWEG01.pdf
驱动芯片：SSD1306 文件:SSD1306-Revision 1.1.pdf

原理

I2C接口

I2C（Inter－Integrated Circuit）总线是由PHILIPS公司开发的两线式串行总线。I2C 串行总线有两根信号线：一根双向的数据线 SDA；另一根是时钟线 SCL。所有接到 I2C 总线上的设备的串行数据都接到总线的 SDA 线，各设备的时钟线 SCL接到总线的 SCL，每个设备都有唯一的地址。

I2C通讯接法如下：

文件:Advance9 2.jpg

600px

原理图

文件:Advance9 3.jpg

600px

本讲实际接线采用了Microduino Weather模块，将OLED转接线直接插在Microduino Weather模块上即可。

文件:Advance9 4.jpg

600px

注意:OLED转接线不要用错。SCL接Microduino-CoreSTM32/zh的SCL，SDA接Microduino-CoreSTM32/zh的SDA,

程序

用到的库：Wire库

#include <Wire.h>
unsigned char  show1[]=
{
        0x00,0x03,0x05,0x09,0x11,0xFF,0x11,0x89,0x05,0xC3,0x00,0xE0,0x00,0xF0,0x00,0xF8,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x44,0x28,0xFF,0x11,0xAA,0x44,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x83,0x01,0x38,0x44,0x82,0x92,
	0x92,0x74,0x01,0x83,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x44,0xFF,0x01,0x7D,
	0x7D,0x7D,0x01,0x7D,0x7D,0x7D,0x7D,0x01,0x7D,0x7D,0x7D,0x7D,0x7D,0x01,0xFF,0x00,
	0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x00,0x00,0x00,0x00,
	0x00,0x00,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,
	0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F,0x3F,0x03,0x03,
	0xF3,0x13,0x11,0x11,0x11,0x11,0x11,0x11,0x01,0xF1,0x11,0x61,0x81,0x01,0x01,0x01,
	0x81,0x61,0x11,0xF1,0x01,0x01,0x01,0x01,0x41,0x41,0xF1,0x01,0x01,0x01,0x01,0x01,
	0xC1,0x21,0x11,0x11,0x11,0x11,0x21,0xC1,0x01,0x01,0x01,0x01,0x41,0x41,0xF1,0x01,
	0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x11,0x11,0x11,0x11,0x11,0xD3,0x33,
	0x03,0x03,0x3F,0x3F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0xE0,0x00,0x00,
	0x7F,0x01,0x01,0x01,0x01,0x01,0x01,0x00,0x00,0x7F,0x00,0x00,0x01,0x06,0x18,0x06,
	0x01,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x40,0x40,0x7F,0x40,0x40,0x00,0x00,0x00,
	0x1F,0x20,0x40,0x40,0x40,0x40,0x20,0x1F,0x00,0x00,0x00,0x00,0x40,0x40,0x7F,0x40,
	0x40,0x00,0x00,0x00,0x00,0x60,0x00,0x00,0x00,0x00,0x40,0x30,0x0C,0x03,0x00,0x00,
	0x00,0x00,0xE0,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x07,0x06,0x06,
	0x06,0x06,0x04,0x04,0x04,0x84,0x44,0x44,0x44,0x84,0x04,0x04,0x84,0x44,0x44,0x44,
	0x84,0x04,0x04,0x04,0x84,0xC4,0x04,0x04,0x04,0x04,0x84,0x44,0x44,0x44,0x84,0x04,
	0x04,0x04,0x04,0x04,0x84,0x44,0x44,0x44,0x84,0x04,0x04,0x04,0x04,0x04,0x84,0x44,
	0x44,0x44,0x84,0x04,0x04,0x84,0x44,0x44,0x44,0x84,0x04,0x04,0x04,0x04,0x06,0x06,
	0x06,0x06,0x07,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x10,0x18,0x14,0x12,0x11,0x00,0x00,0x0F,0x10,0x10,0x10,
	0x0F,0x00,0x00,0x00,0x10,0x1F,0x10,0x00,0x00,0x00,0x08,0x10,0x12,0x12,0x0D,0x00,
	0x00,0x18,0x00,0x00,0x0D,0x12,0x12,0x12,0x0D,0x00,0x00,0x18,0x00,0x00,0x10,0x18,
	0x14,0x12,0x11,0x00,0x00,0x10,0x18,0x14,0x12,0x11,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,
	0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x7F,0x03,0x0C,0x30,0x0C,0x03,0x7F,0x00,0x00,0x38,0x54,0x54,0x58,0x00,0x00,
	0x7C,0x04,0x04,0x78,0x00,0x00,0x3C,0x40,0x40,0x7C,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xAA,0xAA,0xAA,
	0x28,0x08,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
	0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x03,0x0C,0x30,0x0C,0x03,0x7F,
	0x00,0x00,0x26,0x49,0x49,0x49,0x32,0x00,0x00,0x7F,0x02,0x04,0x08,0x10,0x7F,0x00
};
void setup()
{ 
    Wire.begin(18,19);//18--SDA   19--SCL
    SerialUSB.println(" I2C Initializing... ");
    Initial_OLED();
    SerialUSB.println(" OLED 42242Initializing... ");
    delay(5);
}
void loop() 
{
  fill_picture(0xff);  
  delay(1000);    
  fill_picture(0xf0); 
  delay(1000);  
  picture_1();//display a picture
  delay(1000);
}
void Write_IIC_Command(unsigned char IIC_Command)
{
   Wire.beginTransmission(0x3C);  //slave address  011110+SA0+RW  - 0x3C or 0x3D
   Wire.send(0x00);	          //write command
   Wire.send(IIC_Command); 
   Wire.endTransmission();
}
void Write_IIC_Data(unsigned char IIC_Data)
{
   Wire.beginTransmission(0x3C);
   Wire.send(0x40);		//write data
   Wire.send(IIC_Data); 
   Wire.endTransmission();
}
void Initial_OLED()
{
  Write_IIC_Command(0xAE);        //display off
  Write_IIC_Command(0x20);	//Set Memory Addressing Mode	
  Write_IIC_Command(0x10);	//00,Horizontal Addressing Mode;01,Vertical Addressing Mode;10,
                                //Page Addressing Mode (RESET);11,Invalid
  Write_IIC_Command(0xb0);	//Set Page Start Address for Page Addressing Mode,0-7
  Write_IIC_Command(0xc8);	//Set COM Output Scan Direction
  Write_IIC_Command(0x00);        //---set low column address
  Write_IIC_Command(0x10);        //---set high column address
  Write_IIC_Command(0x40);        //--set start line address
  Write_IIC_Command(0x81);        //--set contrast control register
  Write_IIC_Command(0x7f);
  Write_IIC_Command(0xa1);        //--set segment re-map 0 to 127
  Write_IIC_Command(0xa6);        //--set normal display
  Write_IIC_Command(0xa8);        //--set multiplex ratio(1 to 64)
  Write_IIC_Command(0x3F);        //
  Write_IIC_Command(0xa4);        //0xa4,Output follows RAM content;0xa5,Output ignores RAM content
  Write_IIC_Command(0xd3);        //-set display offset
  Write_IIC_Command(0x00);        //-not offset
  Write_IIC_Command(0xd5);        //--set display clock divide ratio/oscillator frequency
  Write_IIC_Command(0xf0);        //--set divide ratio
  Write_IIC_Command(0xd9);        //--set pre-charge period
  Write_IIC_Command(0x22);        //
  Write_IIC_Command(0xda);       //--set com pins hardware configuration
  Write_IIC_Command(0x12);
  Write_IIC_Command(0xdb);       //--set vcomh
  Write_IIC_Command(0x20);   
  Write_IIC_Command(0x8d);     //--set DC-DC enable
  Write_IIC_Command(0x14);    //
  Write_IIC_Command(0xaf);    //--turn on oled panel 
}
void fill_picture(unsigned char fill_Data)
{
  unsigned char m,n;
  for(m=0;m<8;m++)
  {
    Write_IIC_Command(0xb0+m);		//page0-page1
    Write_IIC_Command(0x00);		//low column start address
    Write_IIC_Command(0x10);		//high column start address    
    for(n=0;n<128;n++)
    {
      Write_IIC_Data(fill_Data);
    }  
  }
}
void picture_1()
{
  unsigned char x,y;
  unsigned int i=0;
  for(y=0;y<8;y++)
    {
      Write_IIC_Command(0xb0+y);
      Write_IIC_Command(0x00);
      Write_IIC_Command(0x10);
      for(x=0;x<128;x++)
        {
          Write_IIC_Data(show1[i++]);
        }
    }
}

程序说明：

程序实现了两次刷屏和一次图片的循环显示。
本教程需要使用Wire库，在初始化I2C时不能用Wire.begin()初始化，因为库里默认的SDA和SCL为20和21引脚，需要用Wire.begin(18,19)初始化，或者在Wire.h文件中的引脚定义改为18和19。
Initial_OLED()为初始化OLED显示屏。
show1[]数组保存一张图片，在picture_1()调用显示。

调试

步骤一：连接好电路。

文件:Advance9 5.jpg

600px

步骤二：复制程序代码到Maple IDE编译。

步骤三：下载程序代码，观察OLED显示屏的变化。

结果

由上而下依次变白，

文件:Advance9 6.jpg

600px

1s后，OLED显示由上而下而显示黑白相间图片。

文件:Advance9 7.jpg

600px

1s后，显示一张图片。1s后重复上述过程。

文件:Advance9 8.jpg

600px

视频

视频地址：

OLED显示屏使用

目录

目的

设备

文档

原理

I2C接口

原理图

程序

调试

结果

视频

导航菜单

个人工具

名字空间

变种

视图

更多

搜索

Welcome

创客大赛

软件下载

模块套件

应用套件

硬件

帮助

工具