Microduino-Joypad Getting start

Microduino modules needed Module Number Function Microduino-Joypad 1 Remote controller Microduino-Core 1 Core board Microduino-USBTTL 1 Program download Other Equipment Module Number Function USB cable 1 Data transmission Battery box 1 Battery load 7th battery 3 Power supply 文件:Microduino Joypad TFT-all.jpg 600px Step 1: Install Microduino-TFT on the panel of Microduino-Joypad; 文件:Microduino Joypad TFT-1.jpg 600px 文件:Microduino Joypad TFT-2.jpg 600px Step 2: Fixate plastic fasteners on Microduino-Joypad; 文件:Microduino Joypad nilong-1.jpg 600px Step 3: Stack Microduino-USBTTL, Microduino-Core on the base board of Microduino-Joypad. 文件:Microduino Joypad Module-1.jpg 600px Step 4: Connect Microduino-TFT and Microduino-Joypad through adapter cable; 文件:Microduino Joypad 1.jpg 600px Step 5: Fixate the panel and the base board with plastic fasteners; 文件:Microduino Joypad face bord-1.jpg 600px Step 6: If there is vibration, please install vibration motor; 文件:Microduino Joypad shock-1.jpg 600px Step 7: Connect the battery box on the base board and make sure the electrodes are connected correctly, then paste the board at the bottom of Microduino-Joypad; 文件:Microduino Joypad power 1.jpg 600px Step 8: You can power on and see if the power supply works fine or not. 文件:Microduino Joypad switch-2.jpg 600px If you want to install Microduino-Joypad-Game board, you need to take off the right joystick. 文件:Microduino Joypad keyboard 1.jpg 600px Connect the interface of the key and the base board on the panel by a connector. 文件:Microduino Joypad keyboard 2.jpg 600px Fixate the panel with fasteners. 文件:Microduino Joypad keyboard 3.jpg 600px Test Two parallel UPIN27 base boards; Two switches; Four buttons; MIC sound detection input; Photosensitive detection input; Buzzer output, connected to D6 pin of Microduino; Vibration motor output, connected to D8 pin of Microduino; On-board Micro USB power supply, charging management and 3.3V stability. 2.54-inch pitch for power supply interface. 文件:Microduino-Joypad-Expansion.png Microduino-Joypad-Expansion Libraries needed: https://github.com/wasdpkj/libraries You'll need _01_Microduino_TFT and _08_Microduino_Shield_Joypad Debugging: Hardware needed: Microduino-USBTTL, Microduino-Core and the equipped Microduino-Joypad Software needed: libraries and Arduino IDE; Decompress and download the library file and copy it to libraries of Arduino IDE; Decompress and download library file and then copy it to libraries of Arduino IDE; Re-open “Arduino-IDE” and you can select examples in “_08_Microduino_Shield_Joypad\examples”. After successful compiling, choose the board Microduino Core (Atmega328P@16M,5V) and then download; Program Description Read: Read the value of A and B about illumination, MIC, extension interface. The return value should be within int(0~1023); //Illumination---------------------- Joypad.readLightSensor(); //MIC-------------------- Joypad.readMicrophone(); //INTA---------------------- Joypad.readIntA(); //INTB---------------------- Joypad.readIntB(); Read values of the left and the right analog joysticks. The return value is: int(-512~512); //Left analog joystick---------------- Joypad.readJoystickX(); Joypad.readJoystickY(); //Right analog joystick---------------- Joypad.readJoystick1X(); Joypad.readJoystick1Y(); Read the left and the right analog joystick values; The return value of the left-and-right analog joystick, switches, four-group-of-button are: Boolean(HIGH、LOW)； Joypad.readButton(byte ch); //Left analog joystick---------------- JOYSTICK_UP; JOYSTICK_DOWN; JOYSTICK_LEFT; JOYSTICK_RIGHT; //Left analog joystick press------------ CH_JOYSTICK_SW //Right analog joystick---------------- JOYSTICK1_UP; JOYSTICK1_DOWN; JOYSTICK1_LEFT; JOYSTICK1_RIGHT; //Right analog joystick press ------------ CH_JOYSTICK1_SW //Switch ------------------ CH_SWITCH_L; CH_SWITCH_R; //Four groups of buttons------------------ CH_SWITCH_1; CH_SWITCH_2; CH_SWITCH_3; CH_SWITCH_4; Write: Control buzzer and vibration; //========================== //Buzzer--------------------- Joypad.tone(unsigned int freq); Joypad.tone(unsigned int freq, unsigned long duration); Joypad.noTone(); //Vibration------------------------ Joypad.motor(unsigned int motor_vol); “unsigned int motor_vol”：Vibration intensity Start Application Microduino-Joypad Application Tutorial