Microduino-CC3000

文件:Microduino-CC3000-rect.jpg Microduino-CC3000 Microduino-CC3000 is a well-equipped wireless network processor, which simplifies the implementation process of Internet connectivity. SimpleLink ™ Wi-Fi can significantly reduce a host microcontroller (MCU) software requirements, making it ideal for use in any low-cost and low-power MCU solution for embedded applications.

Features SimpleLink ™ Wi-Fi can significantly reduce a host microcontroller (MCU) software requirements;* Toggle switch controls the charging and discharging, reboot and sleep mode; SimpleLink ™ Wi-Fi SmartConfig ™ technology, a unique one-step activation process of Wi-Fi; Small, cheap, stackable, opened platform; Open source hardware circuit design, compatible with the Arduino IDE development environment for programming; Define unified interface Microduino specification and contain rich peripheral modules. Set up the quick connection with other Microduino modules and sensors easily and flexibly. 2.54 pitch row female connector for easy integration into breadboard.

Specifications Wireless Network Processor IEEE 802.11 b/g Embedded IPv4 TCP/IP stack The best performance in radio industry Tx power：11Mbps CCK with +18dBm Rx sensitivity: 11Mbps CCK with -82dBm Work together with a low-cost microcontroller which using compact memory package and process a million instructions per second (MIPS) 2K bytes Flash 250 bytes RAM Low power consumption Use the FET, shutdown mode current is less than 5uA Operating temperature range -20°C ~ 70°C Authenticated by U.S. Federal Communications Commission(FCC), Industry Canada(IC) and Council of Europe (CE) Based on Texas Instruments (TI)'s seventh generation Wi-Fi solutions. 文件:CC3000-Pinout-2.jpg Microduino-CC3000-Pinout

About SmartConfig SimpleLink ™ Wi-Fi SmartConfig ™ technology, a unique one-step activation process of Wi-Fi that is the developer or end-user, through other devices, such as smart phones, tablet PCs installed SmartConfig App program, and through the program CC3000 is equipped with a hardware circuit to configure current wireless network information of Wifi environment, such as: SSID, wireless password, security authentication, and so on. Just one simple step can make no more than one display device connected to Wifi network to solve wirelessly connect to your home network and the cloud.

Pins CC3000 expansion board is used as a slave on the SPI bus, SPI master to communicate with Microduino CC3000 Module Pin CC3000 Chip Pin Micorduino Pin Function SCK 17 D13 SIP Bus clock DI 15(DIN) D12 Microduino sends data to CC3000 DO 13(DOUT) D11 CC3000 sends data to Micorduino CS 12 D10 SPI Chip-select signal IRQ 14 D2 Interrupt(INT0) EN 26 D9 Microduino set this PIN to high to enable CC3000

Documents Eagle PCB 文件:Microduino-CC3000.zip Main Components TI CC3000 IEEE 802.11b/g solution：WG1300-00 WLAN Module 文件:WG1300-00-DTS-R04.pdf Level converter chip：TC74HC4050 文件:TC74HC4050AF.pdf 2.4G antenna：AT8010-T2R9HAA 文件:AT8010-T2R9HAA.pdf TI Official SPI Stack TI Official WIKI

Development Make sure +3.3 v power supply current can reach 200ma, not recommended for using FT232R debugging directly because FT232R output +3.3 v current is too small. The FT232R datasheet says you can draw up to 50 mA from its 3.3V output. Arduino library and supported package 【CC3000Patch libraygithub download 】 【Adafruit_CC3000 libraygithub download 】 【U8glib libraygoogle download 】 Note for how to use the library CC3000 patch libry is used for upgarde the firmware and can't run it with Adafruit_CC3000's libray. If you want to make these two libraries compatible Microduino Core+： You need open the “Adafruit_CC3000_4Patching.cpp”（CC3000Patch）or “Adafruit_CC3000.cpp”（Adafruit_CC3000）in library's fold firstly； Find line that“#elif defined(__AVR_ATmega1281__) || defined(__AVR_ATmega2561__) || defined(__AVR_ATmega2560__) || defined(__AVR_ATmega1280__)” in file； Add this “ || defined(__AVR_ATmega1284P__) || defined(__AVR_ATmega644P__) ” in the tial of the last line. CC3000Patch： CC3000Patch can be used to upgarde the firmware of CC3000，you need copy the CC3000Patch.ino to "\examples\CC3000Patch\"； You need set the IRP,VBAT and CI correctly in your program,as follows:“#define CC3000_IRQ 2 ”、“#define ADAFRUIT_CC3000_VBAT 9”、“#define ADAFRUIT_CC3000_CS 10”； Detailed usage, please refer to author's README Adafruit_CC3000： You need set the IRP,VBAT and CI correctly in your program,as follows:“#define CC3000_IRQ 2 ”、“#define ADAFRUIT_CC3000_VBAT 9”、“#define ADAFRUIT_CC3000_CS 10” Application Upgrade the frimware of CC3000 Recommend that upgarde the firmware of CC3000 to 1.24 using CC3000Patch，detaile usage refer to author's README （Note：Firmware upgrade process is operated via the serial port monitor, set the Arduino IDE newline terminator serial monitor is set to "newline and carriage return") After upgraed, delete the CC3000Patch library，and then start the Adafruit_CC3000 libray，you can run the included examples！ SimpleLink™ Wi-Fi SmartConfig™ Function If you want to use SimpleLink™ Wi-Fi SmartConfig™ function: Take the IOS as example，download the "TI WIFI SMARTCINFIG" from App Store firstly； Connect the IOS device to router，open the "TI WIFI SMARTCINFIG"，fill the route key in Password； Download the SmartConfigCreate to Microduino from the Adafruit_CC3000 library's examples； Open the serial port monitor（baud rade:115200），When “Waiting for a SmartConfig connection (~60s) ...” displayed，click the "Start" of TI WIFI SMARTCINFIG，waiting for result。 Bug History Picture 正面 背面 Video Texas Instruments SimpleLink™ Wi-Fi SmartConfig™Technology