“Connection Method for New Version”的版本间的差异

来自Microduino Wikipedia
跳转至: 导航搜索
 
(未显示2个用户的2个中间版本)
第25行: 第25行:
 
|Microduino-BT||Microduino-USBTTL
 
|Microduino-BT||Microduino-USBTTL
 
|-
 
|-
|RX0||TX1
+
|D4||TX1
 
|-
 
|-
|TX1||RX0
+
|D5||RX0
 
|-
 
|-
 
|3V3 ||3V3
 
|3V3 ||3V3
第35行: 第35行:
 
|}
 
|}
  
[[File:BT-USBTTL-new-3.jpg|600px|center|thumb]]
+
[[File:BT-USBTTL-new-1.jpg|600px|center|thumb]]
  
 
You need to open Arduino IDE serial monitor or downloaded CommAssistant and set up as follows: Baud rate: 9600; Data bit: 8; Stop bit: 1; Check bit: None.  Besides, please make sure AT instruction ended with new line, 0x0D 0x0A and “\r\n”.   
 
You need to open Arduino IDE serial monitor or downloaded CommAssistant and set up as follows: Baud rate: 9600; Data bit: 8; Stop bit: 1; Check bit: None.  Besides, please make sure AT instruction ended with new line, 0x0D 0x0A and “\r\n”.   
第65行: 第65行:
 
[[File:Microduino-BLE-connect-6.png|center]]
 
[[File:Microduino-BLE-connect-6.png|center]]
 
|}
 
|}
 +
Power off the slave machine and set power-on connection mode for host machine. Enter “AT+IMME1” in serial data sending box and when it returns to “OK+Set:1 Hello World Central”, it means the setup is successful. This, it can be connected even when powers off.
 +
[[File:Microduino-BLE-connect-4.png|center]]
 
You can also control AT instruction via core if you think dupont line connection is boring.   
 
You can also control AT instruction via core if you think dupont line connection is boring.   
 
*Here we adopt D4, D5 serial port to debug.   
 
*Here we adopt D4, D5 serial port to debug.   

2015年10月15日 (四) 08:36的最新版本

  • You need to use AT instruction to set up some parameters via the serial port. So you can refer to the following module handbook:

文件:Microduino-Ble.pdf

  • Module Needed
Related Hardware Number Function
Microduino-BT 2 For communication connection
Microduino-USBTTL 1 For serial port communication debugging
Dupont line 4 For circuit connection
USB cable 2 For power supply
  • We must set one module as the master machine and another as the slave machine. The master machine will search the requirement of the slave machine and then match them. When we start to build the hardware and connect Microduino-BT and Microduino-USBTTL, we need to connect four wires:
Microduino-BT Microduino-USBTTL
D4 TX1
D5 RX0
3V3 3V3
GND GND

You need to open Arduino IDE serial monitor or downloaded CommAssistant and set up as follows: Baud rate: 9600; Data bit: 8; Stop bit: 1; Check bit: None. Besides, please make sure AT instruction ended with new line, 0x0D 0x0A and “\r\n”.

The default baud rate of the BT module is 9600, however, the baud rate of our quadcopter is 115200. So we need to change the baud rate.

  • Slave machine setup

Select a module as the slave machine and connect the wire according to pin. Open the serial monitor, select 9600 baud rate and “Both NL & CR” and input “AT” in the serial data sending box and enter. If the return is “OK”, it means the serial communication of the module has no problem.


Change the baud rate as “115200” and enter “AT+BAUD4” in the serial data sending box and enter. If the return is “ok+set:4”, it means the setup is successful. You can change the baud rate of the serial monitor as “115200” and send “AT” to have a test. 更

In that way, the slave machine is set. You need to other power supply device to supply the electricity, waiting for being connected by the host machine.

  • Host machine setup

Open the serial monitor, select baud rate 9600 and “Both NL & CR” and input “AT” in the serial port data sending box. If the return is “ok”, it means the serial communication of the module is fine. Change the baud rate as “115200” and enter “AT+BAUD4” in the serial data sending box and enter. If the return is “ok+set:4”, it means the setup is successful. You can change the baud rate of the serial monitor as “115200” and send “AT” to have a test.

Change the mode of the host machine, input “AT+ROLE1” in the serial port data sending box. If the return shows “OK+Set:1 Hello World Central”, then the host machine setup is successful.

Set power-on connection mode, input “AT+IMME1” in the serial port data sending box. If the return show “OK+Set:1 Hello World Central”, it means the setup is successful.

Search slave machine device, input “AT+DISC?” in the serial data sending box and go back to your slave machine BT MAC address.

Connect the slave machine, input “AT+COND05FB800D68D” in the serial data sending box and have the connection with the slave machine. If the connection goes well, the slave machine will output “Connected” and the host machine will show “Connected” after about 23 seconds after updating parameters, meaning the BT connection is successful and the system enters transmission mode.

Power off the slave machine and set power-on connection mode for host machine. Enter “AT+IMME1” in serial data sending box and when it returns to “OK+Set:1 Hello World Central”, it means the setup is successful. This, it can be connected even when powers off.

You can also control AT instruction via core if you think dupont line connection is boring.

  • Here we adopt D4, D5 serial port to debug.

Program:

#include <SoftwareSerial.h>
SoftwareSerial mySerial(4, 5); // RX, TX

void setup()  
{
  // Open serial communications and wait for port to open:
  Serial.begin(9600);
  // set the data rate for the SoftwareSerial port
  mySerial.begin(9600);
}

void loop() // run over and over
{
  if(Serial.available())  
  {
    mySerial.write(Serial.read());
  }
  if(mySerial.available())  
  {
    Serial.write(mySerial.read());
  }
}

You can connect according to steps above after the program download. |}