“Microduino-Joypad Getting start”的版本间的差异

Step 7: Connect the battery box on the base board and make sure the electrodes are connected correctly, then paste the board at the bottom of Microduino-Joypad;

文件:Microduino Joypad power 1.jpg

600px

Step 8: You can power on and see if the power supply works fine or not.

文件:Microduino Joypad switch-2.jpg

600px

If you want to install Microduino-Joypad-Game board, you need to take off the right joystick.

文件:Microduino Joypad keyboard 1.jpg

600px

Connect the interface of the key and the base board on the panel by a connector.

文件:Microduino Joypad keyboard 2.jpg

600px

Fixate the panel with fasteners.

文件:Microduino Joypad keyboard 3.jpg

600px

Test

Two parallel UPIN27 base boards;
Two switches;
Four buttons;
MIC sound detection input;
Photosensitive detection input;
Buzzer output, connected to D6 pin of Microduino;
Vibration motor output, connected to D8 pin of Microduino;
On-board Micro USB power supply, charging management and 3.3V stability.
2.54-inch pitch for power supply interface.

文件:Microduino-Joypad-Expansion.png

Microduino-Joypad-Expansion

Libraries needed:
- https://github.com/wasdpkj/libraries

You'll need _01_Microduino_TFT and _08_Microduino_Shield_Joypad

Debugging:
- Hardware needed: Microduino-USBTTL, Microduino-Core and the equipped Microduino-Joypad
- Software needed: libraries and Arduino IDE;
- Decompress and download the library file and copy it to libraries of Arduino IDE; Decompress and download library file and then copy it to libraries of Arduino IDE;
- Re-open “Arduino-IDE” and you can select examples in “_08_Microduino_Shield_Joypad\examples”. After successful compiling, choose the board Microduino Core (Atmega328P@16M,5V) and then download;

Program Description

Read:
- Read the value of A and B about illumination, MIC, extension interface. The return value should be within int(0~1023);

	//Illumination----------------------
	Joypad.readLightSensor();
	//MIC--------------------
	Joypad.readMicrophone();
	//INTA----------------------
	Joypad.readIntA();
	//INTB----------------------
	Joypad.readIntB();

- Read values of the left and the right analog joysticks. The return value is: int(-512~512);

	//Left analog joystick----------------
	Joypad.readJoystickX();
	Joypad.readJoystickY();

	//Right analog joystick----------------
	Joypad.readJoystick1X();
	Joypad.readJoystick1Y();

- Read the left and the right analog joystick values; The return value of the left-and-right analog joystick, switches, four-group-of-button are: Boolean(HIGH、LOW)；

	Joypad.readButton(byte ch);
	//Left analog joystick----------------
		JOYSTICK_UP;
		JOYSTICK_DOWN;
		JOYSTICK_LEFT;
		JOYSTICK_RIGHT;
		
	//Left analog joystick press------------
		CH_JOYSTICK_SW
		
	//Right analog joystick----------------
		JOYSTICK1_UP;
		JOYSTICK1_DOWN;
		JOYSTICK1_LEFT;
		JOYSTICK1_RIGHT;
		
	//Right analog joystick press ------------
		CH_JOYSTICK1_SW
		
	//Switch ------------------
		CH_SWITCH_L;
		CH_SWITCH_R;
		
	//Four groups of buttons------------------
		CH_SWITCH_1;
		CH_SWITCH_2;
		CH_SWITCH_3;
		CH_SWITCH_4;

Write:
- Control buzzer and vibration;

//==========================
	//Buzzer---------------------
  Joypad.tone(unsigned int freq);
  Joypad.tone(unsigned int freq, unsigned long duration);
  Joypad.noTone();

//Vibration------------------------
Joypad.motor(unsigned int motor_vol);
“unsigned int motor_vol”：Vibration intensity

Start Application

Microduino-Joypad Application Tutorial

@@ 第1行： / 第1行： @@
+{{Language|Microduino-Joypad Getting start}}
 {| style="width: 800px;"
 |-
 |
-*所需Microduino模块
+*Microduino modules needed
 {|class="wikitable"
 |-
-|模块||数量||功能
+|Module||Number||Function
 |-
-|[[Microduino-Joypad/zh]] ||1||遥控器
+|[[Microduino-Joypad]] ||1||Remote controller
 |-
-|[[Microduino-Core/zh ]]||1||核心板
+|[[Microduino-Core ]]||1||Core board
 |-
-|[[Microduino-USBTTL/zh]]||1||下载程序
+|[[Microduino-USBTTL]]||1||Program download
 |}
-*其他设备
+*Other Equipment
 {|class="wikitable"
 |-
-|模块||数量||功能
+|Module||Number||Function
 |-
-| USB数据线|| 1||数据传输
+| USB cable|| 1||Data transmission
 |-
-| 电池盒 || 1||装载电池
+| Battery box || 1||Battery load
 |-
-| 7号干电池||3 ||提供电源
+|7th battery ||3 ||Power supply
 |}
 [[File:Microduino_Joypad_TFT-all.jpg||600px|center|thumb]]
-*步骤一：将Microduino-TFT安装在Microduino-Joypad面板上；
+*Step 1: Install Microduino-TFT on the panel of Microduino-Joypad;
 [[File:Microduino_Joypad_TFT-1.jpg||600px|center|thumb]]
 [[File:Microduino_Joypad_TFT-2.jpg||600px|center|thumb]]
-*步骤二：将尼龙螺丝安装在Microduino-Joypad上；
+*Step 2: Fixate plastic fasteners on Microduino-Joypad;
 [[File:Microduino_Joypad_nilong-1.jpg||600px|center|thumb]]
-*步骤三：将Microduino-USBTTL、Microduino-Core叠加在Microduino-Joypad底座上。
+*Step 3: Stack Microduino-USBTTL, Microduino-Core on the base board of Microduino-Joypad.
 [[File:Microduino_Joypad_Module-1.jpg||600px|center|thumb]]
-*步骤四：将Microduino-TFT与Microduino-Joypad通过转接线连接起来；
+*Step 4: Connect Microduino-TFT and Microduino-Joypad through adapter cable;
 [[File:Microduino_Joypad_1.jpg||600px|center|thumb]]
-*步骤五：将底板和面板用尼龙螺丝固定好；
+*Step 5: Fixate the panel and the base board with plastic fasteners;
 [[File:Microduino_Joypad_face_bord-1.jpg||600px|center|thumb]]
-*步骤六：如果要有震动，请安装震动马达；
+*Step 6: If there is vibration, please install vibration motor;
 [[File:Microduino_Joypad_shock-1.jpg||600px|center|thumb]]
-*步骤七：将电池盒连接到底板上，注意正负极别接反了，板子背面标注了正负极，并且将底面板粘贴在Microduino-Joypad底部；
+*Step 7: Connect the battery box on the base board and make sure the electrodes are connected correctly, then paste the board at the bottom of Microduino-Joypad;
 [[File:Microduino_Joypad_power_1.jpg||600px|center|thumb]]
-*步骤八：你可以打开电源开关，观察供电是否正常。
+*Step 8: You can power on and see if the power supply works fine or not.
 [[File:Microduino_Joypad_switch-2.jpg||600px|center|thumb]]
-*如果要安装Microduino-Joypad-Game板，你需要把右边的摇杆取下来
+*If you want to install Microduino-Joypad-Game board, you need to take off the right joystick.
 [[File:Microduino_Joypad_keyboard_1.jpg||600px|center|thumb]]
-*将面板上的按键接口和底板接口通过线连接起来
+*Connect the interface of the key and the base board on the panel by a connector.
 [[File:Microduino_Joypad_keyboard_2.jpg||600px|center|thumb]]
-*再用螺丝将面板固定住。
+*Fixate the panel with fasteners.
 [[File:Microduino_Joypad_keyboard_3.jpg||600px|center|thumb]]
-==测试==
+==Test==
-*两个并列的Upin27底座；
+*Two parallel UPIN27 base boards;
-*两个波动开关；
+*Two switches;
-*四个按钮；
+*Four buttons;
-*MIC声音检测输入；
+*MIC sound detection input;
-*光敏检测输入；
+*Photosensitive detection input;
-*蜂鸣器输出，接到Microduino的D6引脚上；
+*Buzzer output, connected to D6 pin of Microduino;
-*震动马达输出，接到Microduino的D8引脚上；
+*Vibration motor output, connected to D8 pin of Microduino;
-*板载Microusb供电、充电管理、3.3V稳压
+*On-board Micro USB power supply, charging management and 3.3V stability.
-*2.54间距电池供电接口。
+*2.54-inch pitch for power supply interface.
 [[File:Microduino-Joypad-Expansion.png|600px|thumb|center|Microduino-Joypad-Expansion]]
-*用到的库：
+*Libraries needed:
-**https://github.com/wasdpkj/libraries 你需要用到_01_Microduino_TFT库和_08_Microduino_Shield_Joypad库
+**https://github.com/wasdpkj/libraries
-*调试：
+You'll need _01_Microduino_TFT and _08_Microduino_Shield_Joypad
-**所需要准备的硬件有：Microduino USBTTL、、Microduino Core、组装好的Microduino-Joypad
+*Debugging:
-**准备的软件有：支持的库文件、Arduino IDE；
+**Hardware needed: Microduino-USBTTL, Microduino-Core and the equipped Microduino-Joypad
-**解压下载库文件，将解压后的库文件拷贝到Arduino IDE 的libraries文件夹中；
+**Software needed: libraries and Arduino IDE;
-**重新打开“Arduino-IDE”，你可以选择库“_08_Microduino_Shield_Joypad\examples”里面的示例，编译通过后，板卡选择Microduino Core (Atmega328P@16M,5V)，直接下载即可；
+**Decompress and download the library file and copy it to libraries of Arduino IDE; Decompress and download library file and then copy it to libraries of Arduino IDE;
-===程序说明===
+**Re-open “Arduino-IDE” and you can select examples in “_08_Microduino_Shield_Joypad\examples”. After successful compiling, choose the board Microduino Core (Atmega328P@16M,5V) and then download;
-*读取:
+===Program Description===
-**读取光照、麦克风，扩展接口A、B的值，返回值为：int(0~1023)；
+*Read:
+**Read the value of A and B about illumination, MIC, extension interface. The return value should be within int(0~1023);
 <source lang="cpp">
-	//光照----------------------
+	//Illumination----------------------
 	Joypad.readLightSensor();
-	//麦克风--------------------
+	//MIC--------------------
 	Joypad.readMicrophone();
 	//INTA----------------------
@@ 第96行： / 第99行： @@
 </source>
-**读取左、右模拟摇杆的值，返回值为：int(-512~512)；
+**Read values of the left and the right analog joysticks. The return value is: int(-512~512);
 <source lang="cpp">
-	//左模拟摇杆----------------
+	//Left analog joystick----------------
 	Joypad.readJoystickX();
 	Joypad.readJoystickY();
-	//右模拟摇杆----------------
+	//Right analog joystick----------------
 	Joypad.readJoystick1X();
 	Joypad.readJoystick1Y();
 </source>
-**读取左、右模拟摇杆值；左、右模拟摇杆按下值、拨档开关、四组按键，返回值为：Boolean(HIGH、LOW)；
+**Read the left and the right analog joystick values; The return value of the left-and-right analog joystick, switches, four-group-of-button are: Boolean(HIGH、LOW)；
 <source lang="cpp">
 	Joypad.readButton(byte ch);
-	//左模拟摇杆----------------
+	//Left analog joystick----------------
 		JOYSTICK_UP;
 		JOYSTICK_DOWN;
@@ 第119行： / 第122行： @@
 		JOYSTICK_RIGHT;
-	//左模拟摇杆按下------------
+	//Left analog joystick press------------
 		CH_JOYSTICK_SW
-	//右模拟摇杆----------------
+	//Right analog joystick----------------
 		JOYSTICK1_UP;
 		JOYSTICK1_DOWN;
@@ 第128行： / 第131行： @@
 		JOYSTICK1_RIGHT;
-	//右模拟摇杆按下------------
+	//Right analog joystick press ------------
 		CH_JOYSTICK1_SW
-	//拨档开关------------------
+	//Switch ------------------
 		CH_SWITCH_L;
 		CH_SWITCH_R;
-	//四组按键------------------
+	//Four groups of buttons------------------
 		CH_SWITCH_1;
 		CH_SWITCH_2;
@@ 第142行： / 第145行： @@
 </source>
-*写入:
+*Write:
-**控制蜂鸣器、振动；
+**Control buzzer and vibration;
 <source lang="cpp">
 //==========================
-	//蜂鸣器---------------------
+	//Buzzer---------------------
    Joypad.tone(unsigned int freq);
    Joypad.tone(unsigned int freq, unsigned long duration);
    Joypad.noTone();
-//振动------------------------
+//Vibration------------------------
 Joypad.motor(unsigned int motor_vol);
-“unsigned int motor_vol”：振动强弱
+“unsigned int motor_vol”：Vibration intensity
 </source>
-==开始应用==
+==Start Application==
-[[Microduino-Joypad 应用教程]]
+[[Microduino-Joypad Application Tutorial]]
 |}

“Microduino-Joypad Getting start”的版本间的差异

2016年1月6日 (三) 01:36的最新版本

Test

Program Description

Start Application

导航菜单

个人工具

名字空间

变种

视图

更多

搜索

Welcome

创客大赛

软件下载

模块套件

应用套件

硬件

帮助

工具