Microduino-GPRS/GSM

Language	English

Microduino-USBHOST Microduino-GPRS/GSM module can get Microduino core board connected to the internet and achieve the function of sending and receiving messages when it is just inserted with a SIM card and follows some simple instructions. Features ESD protection; Capable of being charged by USB, li-ion or other power supply options; Support automatic baud rate detection function; Capable of sending AT instructions and data through the serial port; Small, cheap, stackable and open; Open hardware circuit design and Arduino compatible programming development environment; Uniformed Microduino interface standard and rich peripheral modules, capable of having a fast and flexible connection and extension with other modules and sensors in accord with Microduino interface standard; Easy to be integrated to pegboards with a 2.45-pitch female header connector interface. Specifications Adopt SIM800L module to support four-band GSM/GPRS, whose working band is：GSM850, EGSM900, DCS1800 and PCS1900MHz. Electrical characteristics Working voltage：3.4V ~4.4V； The current consumption is 0.7 mA under the Sleep Mode GPRS data The maximum data transmission rate of GPRS is 85.6 kbps;； Build-in TCP/IP protocol； Encoding format：CS-1, CS-2, CS-3 and CS-4； Support Unstructured Supplementary Service Data(USSD) Serial debugging Support standard full-function serial as well as the transmission rate with a range from 1200bps to 115200bps; Support serial port multiplexing function corresponding to GSM 07.10 protocol； Two Main Compoments: SIM800L module 文件:Microduino-SIM800L-Pinout1.jpg Microduino-SIM800L-Pinout 文件:Microduino-SIM800L-Pinout2.jpg Microduino-SIM800L-Pinout SIM card power and base plant 文件:Microduino-SIM-Pinout1.jpg Microduino-SIM-Pinout 文件:Microduino-SIM-Pinout2.jpg Microduino-SIM-Pinout Document Eagle PCB： 文件:Microduino-GSM.zip Microduino-GSM mudule SIM800L：文件:SIM800L.pdf SIM car power supply and the card base：文件:SIM800L.pdf Development You can use GSM library to test, https://github.com/Microduino/Microduino_Tutorials/tree/master/Microduino_Libraries/_03_Microduino_GSM_SIM800L Note：This library only supports Microduino-core. Application Sending short messages through the example program in the library. Preparation Hardware：Microduino FT232R, Microduino Core, Microduino GSM, USB cable or lithium battery； Software: GSM library, Arduino IDE (version 1.0.3 and higher)； Uncompress the zip folder to libraries of Arduino IDE； Connect the Microduino FT232R and PC using USB cable to download program and monitor the serial port； USB cable or li-ion battery to charge the Microduino GSM module and press the power button for a long time to activate Microduino GSM for about 4 seconds. That the power-on indicator goes on shows a successful start. Debugging Open SendSMS test program in the examples； After it gets compiled successfully, just select the board "Microduino Core (Atmega328P@16M,5V)" and download directly； Open the serial monitor(The serial monitor is set to the format of "Newline" and "Enter" ), set the baud rate, and the "SMS Messages Sender" will be printed; You need to wait for Microduino GSM module reading SIM card about 10 seconds. If that goes well, "GSM initialized" will be displayed and a note will pop up to remind you to input one number. After the input, just press the Enter, it will remind you to write your message. Just send the message and after that,"COMPLETE" will be displayed on the screen if the message gets sent out. Purchase History Picture Microduino-GPRS/GSM Front Microduino-GPRS/GSM Front Microduino-GPRS/GSM Front Microduino-GPRS/GSM Front Video