查看“Microduino-Joypad Getting started”的源代码

{| style="width: 800px;"
|-
|

First, you need to quick started Microduino ,Reference：[[Microduino_Getting_started]]，If you finished it, Go ahead.

*Microduino modules needed  
{|class="wikitable"
|-
|Module||Number||Function 
|-
|[[Microduino-Joypad]] ||1||Remote controller  
|-
|[[Microduino-Core ]]||1||Core board  
|-
|[[Microduino-USBTTL]]||1||Program download
|}
*Other Equipment  
{|class="wikitable"
|-
|Module||Number||Function 
|-
| USB cable|| 1||Data transmission 
|-
| Battery box || 1||Battery load 
|-
|7th battery ||3 ||Power supply 
|}

[[File:Microduino_Joypad_TFT-all.jpg||600px|center|thumb]]

*Step 1: Install Microduino-TFT on the panel of Microduino-Joypad;  
[[File:Microduino_Joypad_TFT-1.jpg||600px|center|thumb]]
[[File:Microduino_Joypad_TFT-2.jpg||600px|center|thumb]]

*Step 2: Fixate plastic fasteners on Microduino-Joypad;  
[[File:Microduino_Joypad_nilong-1.jpg||600px|center|thumb]]

*Step 3: Stack Microduino-USBTTL, Microduino-Core on the base board of Microduino-Joypad. 
[[File:Microduino_Joypad_Module-1.jpg||600px|center|thumb]]

*Step 4: Connect Microduino-TFT and Microduino-Joypad through adapter cable;  
[[File:Microduino_Joypad_1.jpg||600px|center|thumb]]

*Step 5: Fixate the panel and the base board with plastic fasteners;  
[[File:Microduino_Joypad_face_bord-1.jpg||600px|center|thumb]]

*Step 6: If there is vibration, please install vibration motor;  
[[File:Microduino_Joypad_shock-1.jpg||600px|center|thumb]]

*Step 7: Connect the battery box on the base board and make sure the electrodes are connected correctly, then paste the board at the bottom of Microduino-Joypad; 
[[File:Microduino_Joypad_power_1.jpg||600px|center|thumb]]


*Step 8: You can power on and see if the power supply works fine or not.  
[[File:Microduino_Joypad_switch-2.jpg||600px|center|thumb]]

*If you want to install Microduino-Joypad-Game board, you need to take off the right joystick. 

[[File:Microduino_Joypad_keyboard_1.jpg||600px|center|thumb]]

*Connect the interface of the key and the base board on the panel by a connector.  
[[File:Microduino_Joypad_keyboard_2.jpg||600px|center|thumb]]
*Fixate the panel with fasteners.  
[[File:Microduino_Joypad_keyboard_3.jpg||600px|center|thumb]]

==Test==
*Two parallel UPIN27 base boards; 
*Two switches;  
*Four buttons;
*MIC sound detection input; 
*Photosensitive detection input; 
*Buzzer output, connected to D6 pin of Microduino; 
*Vibration motor output, connected to D8 pin of Microduino; 
*On-board Micro USB power supply, charging management and 3.3V stability.  
*2.54-inch pitch for power supply interface.  

[[File:Microduino-Joypad-Expansion.png|600px|thumb|center|Microduino-Joypad-Expansion]]

*Libraries needed: 

**Please make sure you installed Hardware Support Package and library support package for Microduino. How to do it? See:[[Microduino_Getting_started]]
**Please make sure you install _01_Microduino_TFT library and _08_Microduino_Shield_Joypad library in Ardino\arduino-1.0.6\libraries folder



*Debugging: 
**Hardware needed: Microduino-USBTTL, Microduino-Core and the equipped Microduino-Joypad   
**Software needed: libraries and Arduino IDE; 
**Decompress and download the library file and copy it to libraries of Arduino IDE; Decompress and download library file and then copy it to libraries of Arduino IDE; 
**Re-open “Arduino-IDE” and you can select examples in “_08_Microduino_Shield_Joypad\examples”. After successful compiling, choose the board Microduino Core (Atmega328P@16M,5V) and then download; 
===Program Description===
*Read:
**Read the value of A and B about illumination, MIC, extension interface. The return value should be within int(0~1023); 

<source lang="cpp">
	//Illumination----------------------
	Joypad.readLightSensor();
	//MIC--------------------
	Joypad.readMicrophone();
	//INTA----------------------
	Joypad.readIntA();
	//INTB----------------------
	Joypad.readIntB();
</source>

**Read values of the left and the right analog joysticks. The return value is: int(-512~512);     
<source lang="cpp">

	//Left analog joystick----------------
	Joypad.readJoystickX();
	Joypad.readJoystickY();

	//Right analog joystick----------------
	Joypad.readJoystick1X();
	Joypad.readJoystick1Y();
</source>

**Read the left and the right analog joystick values; The return value of the left-and-right analog joystick, switches, four-group-of-button are: Boolean(HIGH、LOW)；  

<source lang="cpp">

	Joypad.readButton(byte ch);
	//Left analog joystick----------------
		JOYSTICK_UP;
		JOYSTICK_DOWN;
		JOYSTICK_LEFT;
		JOYSTICK_RIGHT;
		
	//Left analog joystick press------------
		CH_JOYSTICK_SW
		
	//Right analog joystick----------------
		JOYSTICK1_UP;
		JOYSTICK1_DOWN;
		JOYSTICK1_LEFT;
		JOYSTICK1_RIGHT;
		
	//Right analog joystick press ------------
		CH_JOYSTICK1_SW
		
	//Switch ------------------
		CH_SWITCH_L;
		CH_SWITCH_R;
		
	//Four groups of buttons------------------
		CH_SWITCH_1;
		CH_SWITCH_2;
		CH_SWITCH_3;
		CH_SWITCH_4;
</source>

*Write:
**Control buzzer and vibration;  
<source lang="cpp">
//==========================
	//Buzzer---------------------
  Joypad.tone(unsigned int freq);
  Joypad.tone(unsigned int freq, unsigned long duration);
  Joypad.noTone();

//Vibration------------------------
Joypad.motor(unsigned int motor_vol);
“unsigned int motor_vol”：Vibration intensity  
</source>

==Start Application==
[[Microduino-Joypad Application Tutorial]]
|}