查看“Core STM32 Startup Guide”的源代码

{| style="width: 800px;"
|-
|
=Setup Microduino-CoreSTM32 with Maple IDE (Windows)=

* Download Maple IDE on
**[http://pan.baidu.com/s/1kTklhVD Baidu]
**[https://github.com/wasdpkj/Microduino-IDE/ github]
* Although the document says Maple only supports WinXP 32-bit, but you can also run it on Windows 7 or Windows 8 with some workaroud.
[[File:01_download_maple.png|thumb|center|600px|Download Maple IDE]]

* UnZip the Maple IDE into a folder, like C:\maple\
* If you are using Windows XP, just plug Microduino-CoreSTM32 into your USB port,  Open your Device Manager, you will see a Device named "Maple", with a yellow exclamation.
* Right click on the Maple, Select "Update Driver". Click on "Not this time", then Next.
* Select the following option: Install from a list or specific location (Advanced), and then click Next.
* Select "Search for the best drivers in these locations", Click on "Include this location in the search, and then Browse into folder like "C:\maple\drivers", Click Next.
* You should now have the CoreSTM32 driver installed.

=== If you ar using Windows 7 64bit or Windows 8 ===

Try this http://wiki.leaflabs.com/Maple_IDE_Windows_8_Installation

= Programming Microduino-CoreSTM32 =

* Make sure you have already installed driver of CoreSTM32.If you use the upper software, you should installed all the packate for STM32 module.

* Run Maple IDE, click menu Tools -> Board, select Microduino-CoreSTM32 to RAM if you just want to test the program, or Microduino-CoreSTM32 to Flash if you want to run the program after resetting the board.

= Setup Microduino-CoreSTM32 with ST-Link debugger =

If you have a ST-Link debugger or a STMicroelectronics' Discovery board, you can debug and download programs using ST-Link.

'''ST-Link Debugger connection'''
{| class="wikitable"
|-
! SWD Pin !! JTAG Pin !! Pin Name !! CoreSTM32 Pin !! MCU Pin !! Description
|-
| 1 || 1 || VDD_TARGET || 3V3 || VDD || VDD from the CoreSTM32
|-
| 2 || 9 || SW_CLK || D6 || PA14 || SWD Clock
|-
| 3 || 8 || GND || GND || GND || Ground
|-
| 4 || 7 || SWDIO || D5 || PA13 || SWD Data input/output
|-
| 5 || 15 || NRST || RST || NRST || Reset
|-
| 6 || 13 || SWO || D8 || PB3 || TRACESWO if async trace enabled, not necessary 
|}

= Download bootloader(firmware) using Microduino-USB2TTL =

* Download and install STM32 Flash loader demonstrator from http://www.st.com/web/en/catalog/tools/PF257525

* Download bootloader file from Maple website: http://static.leaflabs.com/pub/leaflabs/maple-bootloader/maple_mini_boot.bin
* Plug CoreARM on USB2TTL module, connect the USB2TTL module(NOT CoreARM) to your computer.

* Open Flash loader demonstrator, when you see the following dialog, press and hold the BUT button, then click the RESET button, and then release the BUT button. Then click "Next"
[[File:STM32 flash loader 1.png|thumb|center|600px|Flash loader - 1]]

* Click Next again on this page
[[File:STM32 flash loader 2.png|thumb|center|600px|Flash loader - 2]]

* Check if the Target is 128K, and all pages are UnProtected, click Next
[[File:STM32 flash loader 3.png|thumb|center|600px|Flash loader - 3]]

* Select "Download to Device", browse to the "maple_mini_boot.bin", click Next
[[File:STM32 flash loader 4.png|thumb|center|600px|Flash loader - 4]]

* Wait for the progress finish. When the Flash loader promts "Download operation finished successfully", your Microduino-CoreSTM32 is OK to use!
[[File:STM32 flash loader 5.png|thumb|center|600px|Flash loader - 5]]


|}