查看“Microduino-【BT】”的源代码

{{Language|Microduino-【BT】}}
{| style="width: 800px;"
|-
|
[[File:Microduino-bt-rect.jpg|400px|thumb|right|Microduino-Shield BT4.0]]
Microduino-Shield BT 4.0 module is a plug-in device that supports Bluetooth 4.0 low energy standard.
Microduino-Shield BT 4.0 module is a bluetooth serial port transparent transmission module, using the 27 PIN standard Microduino interface, supporting the Arduino board and derivatives, such as Microduino core.
The module is designed by player ogre_c.

==Features==
*Microduino-Shield BT4.0 adopts U type 27 PIN interface of Microduino, combining with other Microduino modult to use;
*Microduino-Shield BT4.0 chooses the HM-10 BLE as the bluetooth core module;
*TI CC2540 chip with 256Kb space;
*Support AT instruction, capable of updating baud rate, device name,paring code and other related parameters as needed, flexible to use；
*Small, cheap, stackable;
*Open source hardware circuit design, compatible with the Arduino IDE development environment for programming;
*With uniformed Microduino interface standard and rich peripheral modules, it is flexible and convenient to have a quick connection and extension with other corresponding Microduino modules and sensors; 
*2.54 pitch row female connector for easy integration into breadboard.

==Specifications==
*Communication form: serial transmission;
*Power supply：+3.3VDC 50mA；
*Bluetooth protocol：Bluetooth Specification V4.0 BLE；
*Service support：Central & Peripheral UUID FFE0,FFE1；
*Frequency：2.4GHz ISM band；
*Modulation mode：GFSK(Gaussian Frequency Shift Keying)；
*Power of transmission：≤4dBm；
*Sensitivity：≤-84dBm at 0.1% BER；
*Transmission rate：
**Asynchronous: 6 kbps；
**Synchronous: 6 kbps；
*State indicator：
**Two states：
***Flashing means that the module has been powered but not matched well.
***Always lighting means that the module has been matched well and has started communication.
**By the indicator, it is very easy to the status of the module, which is conveniently.

==Documents==
Eagle PCB '''[[File:Microduino-BT Shield.zip]]'''

===Main component===
**HM-10 Bluetooth module documentation：'''[[File:Bluetooth40 cn.pdf]]'''，'''[[File:Bluetooth40 en.pdf]]'''
**cc2540_datasheet：'''[[File:Cc2540 datasheet.pdf]]'''

==Development==
===Serial communication requirements===
*Default serial configuration：
**Baud rate: 9600
**No check
**Data bits: 8
**Stop bit: 1
*As for Arduino IDE serial monitor：
**Set at："No line terminator"、"9600baud"
*For other serial debug software：
**Baud rate: 9600
**No check
**Data bits: 8
**Stop bit: 1

*We suggest using Microduino-Core32u4 to debug this BT module:
**Microduino-Core32u4 module can use the USB to simulate the serial 0, and BT uses the 32u4's serial 1 (RX0,TX1), so you don't need to change the existing jumper (RX0,TX1) and it won't impact program download or the serial port's function.

*Microduino Shield BT4.0 uses the default serial RX0,TX1 to communicate with Core module, so it can be directly connected with Microduino FT232.

===Use PC to debug===
*Use serial directly：
**No need superimpose the FT232 directly, cross connect the FT232 and Shield BT4.0's RX0,TX1.

===Use FT232R、Core download and debug===
*Use default jumper (RX0、TX1)：
**Unplug the Microduino Shield BT4.0 during download program; 
*If you want to change the jumper cables to meet your requirement：cut the connection between two intermediate of the pad and RX0/TX1, and then connect them to D2, D3(or D9、D10).
**If changed the jumper, need the change the serial connection between Microduino Shield BT4.0 and Core module, change the connection "TX-RX0、RX-TX1" to following:
***TX-D2、RX-D3 (For Core+'s Serial1)
***TX-D9、RX-D10 (all SoftwareSeria libray to resolve)


===Pin description===

:[[file:Microduino-BT-1.jpg|800px|thumb|center|Microduino-BT]]
<br style="clear: left"/>
:[[file:Microduino-BT-2.jpg|800px|thumb|center|Microduino-BT]]
<br style="clear: left"/>

{|class="wikitable"
! rowspan="1" | HM-10 Pin || Microduino Pin || Function
|-
| TX|| RX0（orD2/D9） || serial send pin (TTL)，connect Core's RXD
|-
| RX || TX1（orD3/D10） || serial receive pin (TTL)，connect Core's TXD
|}


*Support AT command to configure and control：'''[[File:Bluetooth40 cn.pdf]]'''，'''[[File:Bluetooth40 en.pdf]]'''

==Application==
===Download progrm===
Test program：'''[[File:BLE debug uart1.zip]]''','''[[File:BLE LightBlue time.zip]]'''

===Shield BT4.0 pass-through data to IOS devices===
*Prepared hardware：Microduino FT232R, Microduino Core, Microduino Shield BT4.0, supported Bluetooth 4.0 devices (iPhone4s upper,iPod touch 5 upper,iPad 3 upper,iPad mini upper)；
*Prepared software: Arduino IDE (1.0 release and upper), Microduino test program (Arduino part), download LightBlue from App Store；
*Start Arduino IED，open the Microduino test program, board type select "Microduino Core (Atmega328P@16M,5V)", download directly；
*Start to set the IOS device：
**start the bluetooth function on IOS device；
**Open LightBlue；
**In "Central" tab find the "HMSoft", then set "Service"-"Characteristics";
**Then you can see the debugging window, click the "Start Notify".
*ASCII data can be seen displayed: "BLE, Time: xxx" after connection success, where xxx is the Core and Shield BT4.0's running time in seconds.

===Use Core 32u4 to debug Shield BT4.0===
*Prepared hardware：Microduino FT232R,Microduino Core 32u4 and Microduino Shield BT4.0;
*Prepared software：Arduino IDE（1.0 releae and upper）, Microduino test program（Arduino part）;
**（32u4 can use USB to simulate the serial 0, but BT use 32u4's serial1 (RX0,TX1), so you can use the existing jumper(RX0,TX1)）;
*Start Arduino IED, open the Microduino test program, board type select "Microduino Core 32u4", download directly;
*Check if the serial communication works:
**Open the serial monitor, then send "AT" (No \r\n after AT), if return "OK", that means configure success.

===Use Core+'s uart1 to debug Shield BT4.0===
*Prepared hardware：Microduino FT232R, Microduino Core+, Microduino Shield BT4.0；
*Prepared software：Arduino IDE (1.0 release and upper), Microduino test program (Arduino part)；
*Other configuration：Suppose the player has changed the jumper which change the serial to D2、D3；
*Start Arduino IED, open Microduino test program, select the board type "Microduino Core (Atmega328P@16M,5V)", download directly；
*Check the serial communication：
**Open the serial monitor,send uppercase “AT”(no \r\n appened), if return “OK”，that means matched.

===Note：If use the Android device to debug, in order to defect the BT module 4.3 release or upper is needed.===

===Microduino-Shield BT4.0 simple testing===
*[http://viewc.com/p/296 Microduino-Shield BT4.0 simple testing] from @颜火山

==Bug==


==History==
*On June 5, 2013, the second time proofing is completed, changed its name to the "Microduino - (BT)" and added the third optional serial port - UART1, divided into 2 version, version 2.1, a module used for HM09;A 4.0 version, module used for HM10.
*On May 10, 2013, the board is completed.

|-
|
==Pictures==
[[file:Microduino-【BT】-t.jpg|thumb|600px|center|Microduino BT 4.0 Front]]
[[file:Microduino-【BT】-b.jpg|thumb|600px|center|Microduino BT 4.0 Back]]

==Video==
|}