查看“Microduino-smartRF”的源代码

{{Language|Microduino-smartRF}}
{| style="width: 800px;"
|-
|
[[File:Microduino smartRF-rect.jpg|400px|thumb|right|Microduino-smartRF]]
Microduino smartRF uses the latest high-performance CC1101 wireless communication chip, which can be widely applied to various short distance wireless communication field 

==Features==
*Highest working rate at 500KBPS, supports 2-FSK, GFSK and MSK modulation;
*Modify baud rate, power, frequency and other related parameters by software;
*High sensitivity (Under 1.2KBPS - 110dDm, 0.1% packet error rate);
*Low power consumption (1.2 KBaud,433 MHZ RX is 15 ma);
*Built-in hardware CRC error detection and control point to multipoint communication address;
*Programmable control output power, the maximum output power is +10dBM;
*Wireless wake up function, support low power electromagnetic wave activation function;

==Specification==
*Low working voltage: 1.9 ~ 3.6V;
*Support 315/433/868/915MHZ ISM frequency band;
*Support 2-FSK、GFSK and MSK modulation；
*Lowest working rate is 1.2 KBPS, up to 500 KBPS;
*Separate 64 byte RX and TX FIFO buffer;
*125 optional channel work, meet the requirements of multipoint communication and frequency hopping communication;
*Support RSSI strong and weak signal detection and carrier listening function;

*Pin description：
{|class="wikitable"
! rowspan="1" |SMARTRF Pin  ||Microduino Pin  || Function
|-
| INT || D2|| General output port
|-
| SCK ||D13 || SPI bus clock
|-
| S0 ||D12 || Data output port
|-
| SI ||D11|| Data input port
|-
| SS ||D10|| SPI interface，select chip

|}

[[file:Micrduino-smartRF.jpg|800px|thumb|center|Microduino-smartRF]]

==Document==
Eagle PCB download：
Main chips
*Chip：'''[[File:CC1101.pdf]]'''

==Development==
Application library downlaod:
https://github.com/Microduino/Microduino_Tutorials/tree/master/Microduino_Libraries/_03_Microduino_SmartRF_CC1101

Test program download：
https://github.com/Microduino/Microduino_Tutorials/tree/master/Microduino_Texting/Microduino_SMARTRF

==Application==
You can download the test program that Microduino supplied, and use the Microduino-OLED module to test Microduino-smartRF.

*Prepared Hardware：Microduino FT232R, Microduino Core and Microduino-smartRF;
*Prepared Software：Microduino's test program (Arduino), Arduino IDE (upper to 1.0 release);
*Two Microduino cores use the Microduino-smartRF to communicate, master machine sends the running time to slave machine and use the OLED to display;
**ceshi_SMARTRF_T is the master machine send program, ceshi_SMARTRF_R is the slave machine receive program.
**Master machine needs Microduino Core and Microduino-smartRF module; Slave machine needs Microduino Core, Microduino-smartRF and MIcroduino-OLED. Microduino FT232R use to download program.
**Use the IDE to open the test program and download to master and slave machine respectively.
**After download, OLED will display "Rec. pack #xx", ”xx” is the time that receives from master machine;
**Restart master machine, timing starts from zero, slave machine's data also updates at the same time.

==Bug==

==History==

==Picture==

==Front==
[[file:Microduino-smartRF-F.JPG|thumb|600px|center|Microduino-smartRF Front]]
==Back==
[[file:MicroduinosmartRF1-b.JPG|thumb|600px|center|Microduino-smartRF Back]]
==Video==
|}