查看“Thermo Cup”的源代码

{{Language| Thermo Cup}}
{| style="width: 800px;"
|-
|
==Objective==
This cup can "sense" water temperature and present light based on program setting with different color. 
[[File: Temp_Cap-cool.jpg|600px|center]]

==Principle==
Temperature and humidity sensor detects environment temperature and humidity and make light present different color in different sections. 
[[File: Temp_Cap-sch.jpg|600px|center]]

==Equipment==
{|class="wikitable"
|-
|Module||Number||Function 
|-
|[[mCookie-CoreUSB]]||1||Core board 
|-
|[[ mCookie-Hub]]||1||Sensor pin board 
|-
| [[mCookie-BM]]||1||Battery management 
|-
| [[Microduino-Temp&Hum]]||1||Temperature and humidity sensor 
|-
| [[Microduino-Color led]]||1||Colored LED light
|}

*Other Equipment:
**Two cells of battery 

 [[File: Temp_Cap_sch.jpg|600px|center]]
==Load the Code==
*Setup 1：Connect CoreUSB and PC/MAC with a USB cable and open Arduino IDE. 
[[File:CoreUSB_Ble_pc.jpg|600px|center]]
*Setup 2：Click file  > Program examples > mCookie >_206_ThermoCup and load the program.  
[[File: ThermoCup-ino.jpg|600px|center]]
*Setup 3：Choose the right board and serial port, download program to CoreUSB. 
[[File: ThermoCup-upload.jpg|600px|center]]
==Code Debugging==
*Calculate temperature and humidity values--"readByAM2321()" function. You can open serial monitor and check the data. 

<source lang="cpp">
void readByAM2321()
{
  AM2321 am2321;
  am2321.read();
  sensor_tem = am2321.temperature / 10.0;
  Serial.println(sensor_tem);
  delay(100);
}
</source>
[[File: ThermoCup-read.jpg|600px|center]]
*Define three temperature values and divide the temperature zone into four sections. You can change the values according to personal needs or add more temperature values. 
<source lang="cpp">
#define temp1    28
#define temp2    30
#define temp3    32
</source>
*Based on the definition for relation between light color and temperature, we set four light RGB values for environment temperature higher than temp1, between temp1 and temp2, between temp2 and temp3 and higher than temp3.  You can try to change RGB values or add more temperature sections and see changes. " strip.Color(R,G,B)" R, G and B represents three primiary colors. 
<source lang="cpp">
  if (sensor_tem <= temp1)
    colorSet(strip.Color(0, 255, 0));
  
  else if (sensor_tem > temp1 && sensor_tem <= temp2)
    colorSet(strip.Color(0, 0, 255));
  
  else if (sensor_tem > temp2 && sensor_tem <= temp3)
    colorSet(strip.Color(255, 255, 0));
  
  else
    colorSet(strip.Color(255, 0, 0));
</source>
*About RGB. 关于RGB。
RGB value is method of defining light color. R(Red), G(Green) and B(Blue) are the three primary colors, whose values is 0-225. The value represents color intensity. Three different kinds of light can be superimposed together to form a variety of colors, such as (0, 225), that is green. 

[[File: ThermoCup_RGB.jpg|600px|center]]

==Hardware Buildup==
*Setup 1：Connect the temp.&hum sensor to the IIC pin of Hub and the colored light to A0. 
[[file: ThermoCup _setup_2.jpg |600px|center]]
*Setup 2：Connect the activated battery box with BM module. 
[[File:CoreUSB_Ble_steup2.jpg|600px|center]]
*Setup 3：Stack all modules without fixed order and finish part of the circuit buildup.
[[File: ThermoCup_steup3.jpg|600px|center]]

==Result==
The sensor detects different temperature data. You can also build a beautiful shell with LEGO. 
[[File: ThermoCup_legao.jpg|600px|center]]

==Video==

|}