Microduino Enc Wired network experiment -302KIT - 版本历史

Pkj：/* Note */

2014-08-22T08:32:31Z

‎Note

Pkj：/* Result */

2014-08-22T08:22:39Z

‎Result

Pkj：/* Debugging */

2014-08-22T08:09:36Z

‎Debugging

Pkj：/* Bill of Materials */

2014-08-22T07:45:31Z

‎Bill of Materials

Pkj：/* Outline */

2014-08-22T07:39:19Z

‎Outline

2014年3月2日 (日) 15:22 Pkj

2014-03-02T15:22:42Z

Pkj：Created page with "{| style="width: 800px;" |- | ==Outline== Project：Microduino Enc Wire Network Experiment Objective：Use the Microduino Enc module to connect the Microduino RJ45 and Microd..."

2014-02-24T06:23:23Z

Created page with "{| style="width: 800px;" |- | ==Outline== Project：Microduino Enc Wire Network Experiment Objective：Use the Microduino Enc module to connect the Microduino RJ45 and Microd..."

新页面

{| style="width: 800px;"
|-
|
==Outline==
Project：Microduino Enc Wire Network Experiment

Objective：Use the Microduino Enc module to connect the Microduino RJ45 and Microduino core. In local network to control 4 LEDs and achive network control.

Difficulty：Elementary

Time-consuming：One hour

Maker：Microduino Studio-YLB
|-
|
==Bill of Materials==
*Microduino equipment：
{|class="wikitable"
|-
|Module||Number||Function
|-
|Microduino-Core(Microduino Core+)||1||Slave, receive control signal
|-
|Microduino FT232R ||1||Download program
|-
|Microduino Enc(Microduino Rj45)||2||Wireless communication
|}
*Other equipment：
{|class="wikitable"
|-
|Router||one
|-
|Network cable||one
|-
|micro usb data cable||one
|-
|LED||Four
|-
|Bread board||one
|-
|Breadboard jumper||one box
|}
[[File:302KIT-module1.jpg|600px|center|thumb|302KIT-module]]
|-
|
==Document==

|-
|
==Debugging==
Step 1：Set up router network

Power on router, and connect the PC to network.

Step 2：Set up hardware

Install all Microduino module, use the extension board Microduino Duo-V for easy debugging.
|-
|
[[File:302KIT-module2.jpg|600px|center|thumb|302KIT-module]]
[[File:302KIT-system.jpg|600px|center|thumb|302KIT-system]]
|-
|
Step 3：Downlaod program

Start Arduino IED, open the Microduino example program, board type choose "Microduino Core (Atmega328P@16M,5V)", download directly.

Step 4：Connect the network cable

Connect the microduino RJ45 to LAN port of router.

Step 5：Control the LED in loacal network

Open a new web page, enter into the address "myip". Microduiono networking success can enter the control interface, or can not be opened.
|-
|
[[File:302KIT-myip.jpg|600px|center|thumb|Myip]]
|-
|
==Result==
Connect the Microduino core to network, control the LED by the button on web page. Press button, LED light, then press again, LED off.

|-
|
==Note==
*Microduino Enc must be used with Microduino RJ45 together.
*Need configure the MAC address and ip address in local network.
==Video==
http://v.youku.com/v_show/id_XNjY1Njg5Nzcy.html
|}

←上一版本		2014年3月2日 (日) 15:22的版本
第1行：		第1行：
		+	{{Language\|Microduino_Enc有线网络实验-302KIT}}
	{\| style="width: 800px;"		{\| style="width: 800px;"
	\|-		\|-

@@ 第89行： / 第89行： @@
 ==Note==
-*Microduino Enc must be used with Microduino RJ45 together.
+*Microduino-Enc must be stacked with Microduino-RJ45 for use, forming networked devices;
-*Need configure the MAC address and ip address in local network.
+*Device network connection needs to configure MAC address and IP address with Ethernet interface inside the LAN.
 ==Video==
 http://v.youku.com/v_show/id_XNjY1Njg5Nzcy.html
 |}

@@ 第83行： / 第83行： @@
 ==Result==
-Connect the Microduino core to network, control the LED by the button on web page. Press button, LED light, then press again, LED off.
+After connecting the Microduino core to the internet, you can control the switch of the LED through the graphical button on the Gateway Control Interface, achieving the network control via the button.
 |-
+|
 ==Note==
 *Microduino Enc must be used with Microduino RJ45 together.

@@ 第54行： / 第54行： @@
 Step 1：Set up router network
-Power on router, and connect the PC to network.
+Power the router and connect the PC to network.
-Step 2：Set up hardware
+Step 2： Build the hardware
-Install all Microduino module, use the extension board Microduino Duo-V for easy debugging.
+Install all Microduino modules needed and adopt the extension board Microduino Duo-V for easy debugging.
 |-
+|
@@ 第65行： / 第65行： @@
 |-
+|
-Step 3：Downlaod program
+Step 3： Download program
-Start Arduino IED, open the Microduino example program, board type choose "Microduino Core (Atmega328P@16M,5V)", download directly.
+Start Arduino IED, open the Microduino example program and choose the board "Microduino Core (Atmega328P@16M,5V)", then download directly.
-Step 4：Connect the network cable
+Step 4：Connect the network
-Connect the microduino RJ45 to LAN port of router.
+Connect Microduino-RJ45 to the LAN port of router.
-Step 5：Control the LED in loacal network
+Step 5：Wired control of the LED lights inside the LAN
-Open a new web page, enter into the address "myip". Microduiono networking success can enter the control interface, or can not be opened.
+Open a new page and enter the "myip" address in the program.You can only enter the control interface when Microduino connects the internet successfully. Otherwise, it can not be opened.
 |-
+|
@@ 第81行： / 第81行： @@
 |-
+|
 ==Result==
 Connect the Microduino core to network, control the LED by the button on web page. Press button, LED light, then press again, LED off.

@@ 第22行： / 第22行： @@
 |Module||Number||Function
 |-
-|Microduino-Core(Microduino Core+)||1||Slave, receive control signal
+|Microduino-Core(Microduino Core+)||1||Served as the slave machine,receiving and controlling signal
 |-
-|Microduino FT232R ||1||Download program
+|Microduino FT232R ||1||For program download
 |-
-|Microduino Enc(Microduino Rj45)||2||Wireless communication
+|Microduino Enc(Microduino Rj45)||2||For wireless communication
 |}
 *Other equipment：
@@ 第35行： / 第35行： @@
 |Network cable||one
 |-
-|micro usb data cable||one
+|micro USB cable||one
 |-
 |LED||Four
@@ 第46行： / 第46行： @@
 |-
+|
 ==Document==

@@ 第4行： / 第4行： @@
+|
 ==Outline==
-Project：Microduino Enc Wire Network Experiment
+Project: Microduino-Enc Wired Networking Experiment
-Objective：Use the Microduino Enc module to connect the Microduino RJ45 and Microduino core. In local network to control 4 LEDs and achive network control.
+Objective：Enable Microduihno-Core to connect with the network via Microduino-Enc and Microduino-RJ45, control four LED lights inside the LAN and achieve network control.
 Difficulty：Elementary
@@ 第15行： / 第15行： @@
 |-
+|
 ==Bill of Materials==
 *Microduino equipment：