http:///https//wiki.microduino.cn/index.php?action=history&feed=atom&title=Microduino-RelayMicroduino-Relay - 版本历史2026-04-29T23:13:33Z本wiki的该页面的版本历史MediaWiki 1.30.0https//wiki.microduino.cn/index.php?title=Microduino-Relay&diff=11101&oldid=prev1304410487@qq.com：Created page with "{{Language|Microduino-Relay }} {| style="width: 800px;" |- | Microduino-Relay Microduino-Relay is a relay module. It can be ..."2015-10-28T07:24:26Z<p>Created page with "{{Language|Microduino-Relay }} {| style="width: 800px;" |- | <a href="/index.php/%E6%96%87%E4%BB%B6:Microduino-Relay.jpg" title="文件:Microduino-Relay.jpg">400px|thumb|right| Microduino-Relay</a> Microduino-Relay is a relay module. It can be ..."</p>
<p><b>新页面</b></p><div>{{Language|Microduino-Relay }}<br />
{| style="width: 800px;"<br />
|-<br />
|<br />
[[File: Microduino-Relay.jpg|400px|thumb|right| Microduino-Relay]]<br />
<br />
Microduino-Relay is a relay module. It can be used in isolation control. <br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
<br />
==Features==<br />
*Used in isolation control of high voltage and high current signal. <br />
<br />
==Specification==<br />
*Input 5V operation voltage for primary side; <br />
*Output 10A 250VAC/10A 30VDC for secondary side; <br />
*1.27mm-pitch 4PIN interface; <br />
*Pin description: GND, VCC, signal input and NC(empty). Since the input signal is simulated, it needs to be driven by digital interface(D0~D13), which can be connected the pins (3~10) of Sensorhub with the corresponding pins(D0,D2,D4,D6,D8,D10,D12). <br />
[[file:mCookie-sensorhub_rule.JPG|thumb|800px|center]]<br />
<br />
[[File: Microduino-Relay_rule1.jpg|600px|thumb|center]]<br />
<br />
==Document==<br />
<br />
*Schematic: '''[[File: Microduino_Relay.Zip]]'''<br />
<br />
==Development==<br />
You can use Microduino-Relay to convert weak signal into high voltage, high current signal or for isolation control. <br />
<br />
==Application==<br />
*All hardware needed: [[Microduino-CoreUSB]], [[Microduino-USBTTL]], [[Microduino-Sensorhub]], dupont lines and USB cable. <br />
*Software: <br />
**Make sure you build Microduino IDE. If not, please refer to: [[Microduino Getting start]]<br />
*Stack all modules and connect the Relay module to D2 port of Sensorhub with a wire. <br />
*Open Arduino IDE, select File→Examples→Digital→BlinkWithoutDelay program examples, choose the right board from Tools→Board and then compile.<br />
*Select the right port from Tools→Serial Port in Arduino IDE after compiling, then download program. <br />
*After download, you'll see STA light on the Relay module blinks one time each second. By measuring 2PIN crimping terminal on the Relay module with a multimeter, you can see that 2PIN crimping terminal also powers on and off each second. <br />
<br />
==Purchase==<br />
<br />
==History==<br />
<br />
==Pictures==<br />
<br />
*Front <br />
[[file: Microduino-Relay-F.JPG|thumb|600px|center|Microduino-Relay Front]]<br />
*Back <br />
[[file: Microduino-Relay -b.JPG|thumb|600px|center|Microduino-Relay Back]]<br />
|}</div>1304410487@qq.com