Microduino-NEO-6M - 版本历史

Pkj：/* Development */

2014-05-10T13:18:12Z

‎Development

2014-03-19T12:31:17Z

Added a picture, showing a working u-center connection (w/ rx/tx crossover)

2014-03-18T04:39:11Z

2014-03-18T04:38:00Z

2014-03-13T01:48:14Z

‎Download and debug program with FT232R and Core Module

2014-02-28T05:35:18Z

‎Document

2014-02-22T03:43:13Z

‎Pin Description

2014-02-22T03:41:24Z

‎Pin Description

2014-02-22T03:39:39Z

‎Pin Description

2014-02-16T01:40:50Z

@@ 第87行： / 第87行： @@
 ==Development==
 * Make sure the +3.3 v power supply current can reach 200ma, not recommended use FT232R debugging directly, because FT232R's output +3.3 v current is too small.
 ===Arduino library and supported package===
@@ 第110行： / 第125行： @@
 **Flicker,（100ms off，900ms on），indicates that module has achieved position successfully.
 *Easy to identify the state of module by PPS indicator.
 ==Application==

@@ 第139行： / 第139行： @@
 **Using the jumper cable cross connect the RX0/TX1 for FT232 and NEO-6M, that is the RX0 of NEO-6M connects to the TX1 of FT232, and the TX1 of NEO-6M connects to RX0 of FT232.
 **Connect the 3V3 pin of NEO-6M module to 3V3 pin of FT232, and connects the GND together.
 . Use the changed jumper mode
 If you have changed the jumper as upper described, you can supperipose FT232, NEO-6M and Core module together, then connect to PC to debug directly.
 ====Use u-center configuration module to update rage====
 *Firstly, place the Microduino NEO-6M into an open area, and then connects to PC by Microduino FT232R;

@@ 第88行： / 第88行： @@
 * Make sure the +3.3 v power supply current can reach 200ma, not recommended use FT232R debugging directly, because FT232R's output +3.3 v current is too small.
-===Arduino库及支持包===
+===Arduino library and supported package===
-*【Adafruit_GPS库'''[https://github.com/adafruit/Adafruit-GPS-Library github download ]''' 】
+*【Adafruit_GPS library'''[https://github.com/adafruit/Adafruit-GPS-Library github download ]''' 】
-*【U8glib库'''[http://code.google.com/p/u8glib/ google download ]''' 】
+*【U8glib library'''[http://code.google.com/p/u8glib/ google download ]''' 】
 *[http://www.u-blox.com/en/evaluation-tools-a-software/u-center/u-center.html u-center-8.0]

@@ 第104行： / 第104行： @@
 *If you use default pin（RX0、TX1）：
 **Unplug the Microduino NEO-6M module when downloading program;
-*If you want to change the jumper cables to meet your requirement:切断两组的焊盘中间与RX0/TX1的连线，将焊盘中间与D2、D3焊上即可。
+*If you want to change the jumper cables to meet your requirement: Cut off the connection between the middle of bonding pad and RX0/TX1, then welding the middle of bonding pad to D2 and D3.
 **If you changed the jumper cables,the serial connect between Microduino NEO-6M and Core should be changed to TX-D2、RX-D3 from connection TX-RX0、RX-TX1（corresponding to Core+'s Serial1）

@@ 第82行： / 第82行： @@
 *GPS module：UBLOX NEO-6M：'''[[File:NEO-6 DataSheet (GPS.G6-HW-09005).pdf]]'''
 *Super capacitor：XH414H '''[[File:XH414H.pdf]]'''
 *NMEA-0183 protocol： '''[[File:NMEA-0183 CN.pdf]]''','''[[File:NMEA-0183 EN.pdf]]'''
 *u-center GPS evaluation software User Guide： '''[[File:U-center GPS evaluation software User Guide.pdf]]'''
 ==Development==

@@ 第72行： / 第72行： @@
 |}
-[[File:NEO-6-Pinout-1.jpg|800px|thumb|center|Microduino-NEO-6-Pinout]]
+[[File:NEO6M-Pinout-2.jpg|800px|thumb|center|Microduino-NEO6M-Pinout]]
-[[File:NEO-6m-Pinout-1.jpg|800px|thumb|center|Microduino-NEO-6m-Pinout]]
+[[File:NEO6M-Pinout-1.jpg|800px|thumb|center|Microduino-NEO6M-Pinout]]
 ==Document==