Microduino-BT - 版本历史

853387039@qq.com：/* APP */

2015-10-15T08:30:14Z

‎APP

2015-10-15T08:02:08Z

‎Serial Port Communication Requirements

2015-08-08T05:48:46Z

‎Main Components

2015-06-04T13:55:20Z

‎Use USBTTL and Core to Download and Debug： Some typos

2015-03-02T08:54:47Z

‎History

2015-03-02T03:58:55Z

2014-12-04T02:29:10Z

2014-11-25T09:59:07Z

2014-11-17T07:06:24Z

2014-11-06T08:46:02Z

‎Application

@@ 第51行： / 第51行： @@
 ===Main Components===
 *cc2541_datasheet：'''[[File:Cc2541.pdf]]'''
-===APP===
+===Android APP===
 *APP Installation package：'''[[File:BT APP.zip]]'''
 *APP Source：https://github.com/iascchen/android-microduino

@@ 第68行： / 第68行： @@
 **No check
 **Data bit 8
-**Stop bit1
+**Stop bit
 ===Use PC to Debug===

@@ 第51行： / 第51行： @@
 ===Main Components===
 *cc2541_datasheet：'''[[File:Cc2541.pdf]]'''
 ==Development==

@@ 第87行： / 第87行： @@
 *If it keeps using the default jumper (RX0、TX1)：
 **Unplug the Microduino Shield BT4.0 during downloading the program;
-*If you want to change the jumper cables to meet your requirement, you need to cut the connection between two intermediate of the pad and RX0/TX1, and then connect them to D2, D3(or D9、D10).
+*If you want to change the jumper cables to meet your requirement, you need to cut the connection between two intermediate of the pad and RX0/TX1, and then connect them to D2, D3 (or D9, D10).
 **If it needs to change the jumper, you can change the serial connection of Microduino Shield BT4.0 and Microduino Core from "TX-RX0、RX-TX1" to:
-***TX-D2、RX-D3 (For Core+'s Serial1)
+***TX-D2, RX-D3 (For Core+'s Serial1)
-***TX-D9、RX-D10 (you can adopt SoftwareSeria libray to solve the problem)
+***TX-D9, RX-D10 (you can adopt SoftwareSerial libray to solve the problem)
 ===Pin Description===

@@ 第149行： / 第149行： @@
 ==History==
-*On June 5, 2013, the second time proofing is completed, changed its name to the "Microduino - (BT)" and added the third optional serial port - UART1, divided into 2 version, version 2.1, a module used for HM09;A 4.0 version, module used for HM10.
+*On July, 28, 2014, the module scheme was cancelled. The new BT version adopts CC25541 chip, supporting iBeacons mode. For the old version, you can refer to [[Microduino-【BT】]].
-*On May 10, 2013, the board is completed.
+*On June 5, 2014, the second proofing was finished, changing its name to <nowiki>Microduino-[BT]</nowiki> and addomg the third optional serial port—UART1. It is divided into two versions—version 2.1, a module used for HM09 and 4.0 version, a module used for HM10.
 |-
+|
 ==Pictures==
 [[file:Microduino-【BT】-t.jpg|thumb|600px|center|Microduino BT 4.0 Front]]

@@ 第4行： / 第4行： @@
+|
 [[File:Microduino-bt-rect.jpg|400px|thumb|right|Microduino-Shield BT4.0]]
-Microduino-Shield BT 4.0 module is a plug-in device that supports Bluetooth 4.0 low energy standard.
+Microduino-BT is a BLE serial transparent transmission module based on CC2541 chip. It is custom-made for U-shaped 27PIN standard interface of Microduino. The old version can refer to [[Microduino-【BT】]].
 ==Features==

←上一版本		2014年12月4日 (四) 02:29的版本
第129行：		第129行：

	==[[ How to Connect Two Microduino-BT Modules]]==		==[[ How to Connect Two Microduino-BT Modules]]==
		+
		+	==[[Intercommunication between Two Microduino-BT Modules]]==

	==[[Microduino BT Serial port Transmits Data to IOS Device]]==		==[[Microduino BT Serial port Transmits Data to IOS Device]]==

@@ 第1行： / 第1行： @@
-{{Language|Microduino-【BT】}}
+{{Language|Microduino-BT}}
 {| style="width: 800px;"
 |-

@@ 第123行： / 第123行： @@
 *Check the serial communication：
 **Open the serial monitor,send the capitalized “AT”( without \r\n behind), if the return shows“OK”，that means a successful configuration.
 ===Note：If you use Android device to debug, you need to make sure the system should be version 4.3 or higher so that Microduino-BT can be detected.===