2018年12月7日 (五) 03:42 502748957@qq.com

2018-12-07T03:42:02Z

2018年5月16日 (三) 09:54 Radiumray9@gmail.com

2018-05-16T09:54:42Z

Radiumray9@gmail.com：创建页面，内容为“=='''基本原理'''== MicroMV捕捉线并计算出需要旋转的角度，通过串口发送给microduino microduino接收数据后控制舵机电机 =='''MicroM…”

2018-05-16T07:16:05Z

创建页面，内容为“=='''基本原理'''== *MicroMV捕捉线并计算出需要旋转的角度，通过串口发送给microduino *microduino接收数据后控制舵机电机 =='''MicroM…”

新页面

=='''基本原理'''==
*MicroMV捕捉线并计算出需要旋转的角度，通过串口发送给microduino
*microduino接收数据后控制舵机电机

=='''MicroMV的代码准备'''==
把lineFollowing.py替换到MicroMV生成的U盘空间中的main.py做为主程序<br />
lineFollowing.py:
<source lang="py">
import sensor, image, time, math, lcd
from pyb import UART
import json
# Tracks a black line. Use [(128, 255)] for a tracking a white line.
# GRAYSCALE_THRESHOLD = [(0, 64)]
GRAYSCALE_THRESHOLD = [(0, 50)]
#设置阈值，如果是黑线，GRAYSCALE_THRESHOLD = [(0, 64)]；
#如果是白线，GRAYSCALE_THRESHOLD = [(128，255)]
# Each roi is (x, y, w, h). The line detection algorithm will try to find the
# centroid of the largest blob in each roi. The x position of the centroids
# will then be averaged with different weights where the most weight is assigned
# to the roi near the bottom of the image and less to the next roi and so on.
ROIS = [ # [ROI, weight]
(0, 100, 160, 20, 0.7), # You'll need to tweak the weights for you app
(0, 050, 160, 20, 0.3), # depending on how your robot is setup.
(0, 000, 160, 20, 0.1)
]
#roi代表三个取样区域，（x,y,w,h,weight）,代表左上顶点（x,y）宽高分别为w和h的矩形，
#weight为当前矩形的权值。注意本例程采用的QQVGA图像大小为160x120，roi即把图像横分成三个矩形。
#三个矩形的阈值要根据实际情况进行调整，离机器人视野最近的矩形权值要最大，
#如上图的最下方的矩形，即(0, 100, 160, 20, 0.7)
# Compute the weight divisor (we're computing this so you don't have to make weights add to 1).
weight_sum = 0 #权值和初始化
for r in ROIS: weight_sum += r[4] # r[4] is the roi weight.
#计算权值和。遍历上面的三个矩形，r[4]即每个矩形的权值。
# Camera setup...
sensor.reset() # Initialize the camera sensor.
sensor.set_pixformat(sensor.GRAYSCALE) # use grayscale.
sensor.set_framesize(sensor.QQVGA) # use QQVGA for speed.
sensor.skip_frames(30) # Let new settings take affect.
sensor.set_auto_gain(False) # must be turned off for color tracking
sensor.set_auto_whitebal(False) # must be turned off for color tracking
#关闭白平衡
clock = time.clock() # Tracks FPS.
lcd.init() # Initialize the lcd screen.
uart = UART(4, 115200)
uart.init(115200, bits=8, parity=None, stop=1) # init with given parameters
while(True):
clock.tick() # Track elapsed milliseconds between snapshots().
img = sensor.snapshot() # Take a picture and return the image.
centroid_sum = 0
#利用颜色识别分别寻找三个矩形区域内的线段
for r in ROIS:
blobs = img.find_blobs(GRAYSCALE_THRESHOLD, roi=r[0:4], merge=True)
# r[0:4] is roi tuple.
#找到视野中的线,merge=true,将找到的图像区域合并成一个
#目标区域找到直线
if blobs:
# Find the index of the blob with the most pixels.
most_pixels = 0
largest_blob = 0
for i in range(len(blobs)):
#目标区域找到的颜色块（线段块）可能不止一个，找到最大的一个，作为本区域内的目标直线
if blobs[i].pixels() > most_pixels:
most_pixels = blobs[i].pixels()
#merged_blobs[i][4]是这个颜色块的像素总数，如果此颜色块像素总数大于 #most_pixels，则把本区域作为像素总数最大的颜色块。更新most_pixels和largest_blob
largest_blob = i
# Draw a rect around the blob.
img.draw_rectangle(blobs[largest_blob].rect())
#将此区域的像素数最大的颜色块画矩形和十字形标记出来
img.draw_cross(blobs[largest_blob].cx(),
blobs[largest_blob].cy())
centroid_sum += blobs[largest_blob].cx() * r[4] # r[4] is the roi weight.
#计算centroid_sum，centroid_sum等于每个区域的最大颜色块的中心点的x坐标值乘本区域的权值
center_pos = (centroid_sum / weight_sum) # Determine center of line.
#中间公式
# Convert the center_pos to a deflection angle. We're using a non-linear
# operation so that the response gets stronger the farther off the line we
# are. Non-linear operations are good to use on the output of algorithms
# like this to cause a response "trigger".
deflection_angle = 0
#机器人应该转的角度
# The 80 is from half the X res, the 60 is from half the Y res. The
# equation below is just computing the angle of a triangle where the
# opposite side of the triangle is the deviation of the center position
# from the center and the adjacent side is half the Y res. This limits
# the angle output to around -45 to 45. (It's not quite -45 and 45).
deflection_angle = -math.atan((center_pos-80)/60)
#角度计算.80 60 分别为图像宽和高的一半，图像大小为QQVGA 160x120.
#注意计算得到的是弧度值
# Convert angle in radians to degrees.
deflection_angle = math.degrees(deflection_angle)
#将计算结果的弧度值转化为角度值
# Now you have an angle telling you how much to turn the robot by which
# incorporates the part of the line nearest to the robot and parts of
# the line farther away from the robot for a better prediction.
# print("Turn Angle: %f" % deflection_angle)
if center_pos!=0:
output_str=json.dumps([deflection_angle])
else:
output_str=json.dumps([0])
# output_str=json.dumps([deflection_angle])
print('you send:',output_str)
uart.write(output_str+'\n')
# uart.write(deflection_angle+'\n')
#将结果打印在terminal中
lcd.display(img)
</source>
IDE运行效果为<br/>
[[File:microMVLineFollowing1.png||600px|left]]<br style="clear: left"/>
屏幕中会对线进行标注

=='''Microduino的代码准备'''==
<source lang="py">
#define my_Serial Serial1
#define servoPin 6
#define LEDPin 4
#include <Servo.h>
#include <Microduino_ColorLED.h> //引用彩灯库
static const uint8_t carPinForward = 8;
static const uint8_t carPinBackward = 9;
uint8_t carPower=40;
// uint8_t carPower=0;
Servo myservo;
String degreeStr;
int pos=0;
int lastPos=0;
ColorLED strip = ColorLED(1, LEDPin);
void setup() {
Serial.begin(115200);
my_Serial.begin(115200);
myservo.attach(servoPin);
strip.begin();
strip.setBrightness(60);
strip.setPixelColor(0, strip.Color(255, 255, 255));
strip.show();
pinMode(carPinForward, OUTPUT);
digitalWrite(carPinForward, LOW);
pinMode(carPinBackward, OUTPUT);
digitalWrite(carPinBackward, LOW);
}
void loop() {
if (my_Serial.available() > 0) {
degreeStr = my_Serial.readStringUntil('\n');
uint8_t len=degreeStr.length();
degreeStr=degreeStr.substring(1,len-1);
pos=degreeStr.toInt();
Serial.println(pos);
if(pos!=0) {
pos = map(pos, -50, 50, 30, 130);
myservo.write(pos);
lastPos=pos;
} else {
if(lastPos>80) {
myservo.write(130);
}else {
myservo.write(30);
}
}
}
uint8_t detlaSpeed=0;
uint8_t detlaSpeed=abs(pos-80);
detlaSpeed=map(detlaSpeed,0,50,0,7);
analogWrite(carPinForward, carPower-detlaSpeed);
digitalWrite(carPinBackward, LOW);
}
</source>

←上一版本		2018年12月7日 (五) 03:42的版本
第168行：		第168行：


−	[[~~MicroMV目录~~\|返回MicroMV目录页面]]	+	[[MicroMV 简介\|返回MicroMV目录页面]]

←上一版本		2018年5月16日 (三) 09:54的版本
第164行：		第164行：
	}		}
	</source>		</source>
		+
		+
		+
		+
		+	[[MicroMV目录\|返回MicroMV目录页面]]

MicroMV 巡线机器人 - 版本历史

2018年12月7日 (五) 03:42 502748957@qq.com

2018年5月16日 (三) 09:54 Radiumray9@gmail.com

Radiumray9@gmail.com：创建页面，内容为“=='''基本原理'''== *MicroMV捕捉线并计算出需要旋转的角度，通过串口发送给microduino *microduino接收数据后控制舵机电机 =='''MicroM…”

Radiumray9@gmail.com：创建页面，内容为“=='''基本原理'''== MicroMV捕捉线并计算出需要旋转的角度，通过串口发送给microduino microduino接收数据后控制舵机电机 =='''MicroM…”