Changliu818@yahoo.com：Changliu818@yahoo.com moved page Talk:Microduino STM32 core (STM32 Compatible) to Talk:STM32 Core: Module Specifications

2015-06-30T18:44:10Z

Changliu818@yahoo.com moved page Talk:Microduino STM32 core (STM32 Compatible) to Talk:STM32 Core: Module Specifications

Ian@fenditton.org：/* What I've found out so far */

2014-12-16T21:35:56Z

‎What I've found out so far

Ian@fenditton.org：Brain dump of where I've got to

2014-11-27T20:14:42Z

Brain dump of where I've got to

新页面

== What I've found out so far ==

* It uses the STM32F103CBT6 chip, as used on the Maple Mini (http://leaflabs.com/docs/hardware/maple-mini.html)
* There are two buttons and an LED. The button on the board edge is a reset, the other button (between the reset button and the USB micro connector) is used to start the STM32's built-in ROM bootloader.
* Normally, there's also Maple bootloader in the flash which lets you load programs using the USB DFU protocol. The Maple IDE will expect to use this.
* The IDE can't automatically reset the Core to upload new sketches. You need to do the following:
** In the IDE, hit the 'upload' button, and watch the messages
** It will compile the sketch, then will wait on 'searching for DFU device'
** As soon as you see this, hit the reset button
** Hopefully, the IDE will see the USB DFU device when the bootloader runs briefly after reset.

* If things get really screwed, you may need to reload the Maple bootloader. To do this:
** Plug a Microduino FT232 board onto the bottom of the core module
** Plug the FT232 board into your USB host, so it powers both boards and appears as a regular (FTDI) serial port e.g. COM6
** Hold down the "ROM bootloader" button, press & release the reset button, then release the bootloader button.
** The STM32's ROM bootloader should now be running and awaiting instructions from the serial port.
** Get & install ST's Flash Loader app (http://www.st.com/web/en/catalog/tools/PF257525) to read and write the core's flash.

* As far as I can tell, the Microduino Core's STM32F103 '''isn't wired up the same as the STM32F103 on Maple or Maple Mini''', meaning the D0-D13 pins (etc) won't work as intended in sketches if you've selected Maple or Maple Mini in the IDE 'Boards' menu.
** For instance, the on-board LED is wired to the Core's PA8 line - this comes out as digital pin 6 when using "Maple R3" settings, and pin 25 when using "Maple Mini" settings.
** Presumably there's a board support package somewhere with a '''boards.txt''' and settings for pin numbers which gets this working. I don't know where this is at the minute.

Cheers
IH
04:14, 28 November 2014 (CST)

←上一版本	2015年6月30日 (二) 18:44的版本
（没有差异）

←上一版本		2014年12月16日 (二) 21:35的版本
第25行：		第25行：
	IH		IH
	04:14, 28 November 2014 (CST)		04:14, 28 November 2014 (CST)
		+
		+	== Pinout table ==
		+
		+	This table was worked out by tracing out the STM32 pins using a multimeter, and is ''not'' based on any official schematic. It may, therefore, contain errors, so use at your own risk!
		+
		+	Cheers
		+	IH

讨论:STM32 Core: Module Specifications - 版本历史

Changliu818@yahoo.com：Changliu818@yahoo.com moved page Talk:Microduino STM32 core (STM32 Compatible) to Talk:STM32 Core: Module Specifications

Ian@fenditton.org：/* What I've found out so far */

Ian@fenditton.org：Brain dump of where I've got to